how to make a paracord zipper pull

How to Make a Paracord Zipper Pull

By Amanda Thompson
AD

Looking to add a touch of tacticalilderness to your gear? Or perhaps you're on a quest to up your DIY game? Either way, creating a paracord zipper pull is a rewarding and practical project, transforming plain zippers into functional survival tools. This step-by-step guide will walk you through the process, combining your love for textures and the great outdoors with essential knot knowledge.

Paracord, short for parachute cord, is a utility rope designed for military use. Tough, versatile, and available in various colors, it's perfect for this project. Plus, it turns your zipper pulls into potential life-savers, with about 7 feet of cord that can be unraveled for emergencies. Now, let's dive into how to make your own paracord zipper pulls.

Choosing Your Materials

Before you begin, gather your materials. You'll need:

AD
5 DIY Paracord Zipper Pulls (with Step-by-Step Photos)
5 DIY Paracord Zipper Pulls (with Step-by-Step Photos)
How to Make a Paracord Zipper Pull
How to Make a Paracord Zipper Pull
the instructions for how to tie a paracord rope with scissors and measuring tape
the instructions for how to tie a paracord rope with scissors and measuring tape

1. Paracord (around 3-4 feet, depending on your zipper length and desired pull length)
2. Scissors
3. Lighter or matches (for securing the ends)
4. Zipper (with two cord channels)

Determine Your Cord Length

Measure your zipper, and decide how long you want your pull to be. Typically, 2-3 inches is ideal, but you can customize this based on your preferences and zipper length.

EASIEST SNAKE KNOT!! Knife Lanyard/Zipper Pull/FOB!! #shorts #bushcraft #outdoors #knots
EASIEST SNAKE KNOT!! Knife Lanyard/Zipper Pull/FOB!! #shorts #bushcraft #outdoors #knots
Make Paracord Zipper Pulls
Make Paracord Zipper Pulls

To create your pull, you'll need two lengths of paracord. So, divide your desired pull length by 2, then subtract the thickness of your zipper to find the length of each paracord section. For example, if you want a 2-inch pull and your zipper is 0.5 inches thick, each paracord section will be (2/2) - 0.5 = 1 inch.

Measure and Cut

Mark and cut two lengths of paracord based on your calculations. It's better to have slightly too much than too little, as excess can be burned off later.

AD

Now that you have your cord sections, it's time to start the braiding process. It might seem complex initially, but with practice, you'll master this slow-stitched F Massimo knot, also known as a 'doubleXII' or 'square knot' in paracord.

Starting the Knot

The first step is to prepare your cord ends. This will make it easier to start your knot.

Take one end of each paracord section and place them parallel, with the rough sides (where the threads are exposed) facing out. This will ensure a neat, non-bulky finished product.

AD

Form the First Loop

Make a bight (a loop) in one of the cords. It should be large enough to feed the other cord through it. The cord on top ( А) goes over and under the cord on the bottom (Б) to create the loop. (А goes around Б, then under Б)

You should now have a loop on the left and a 'U' shape on the right.

Feed the Cord Through

Take the rightmost cord (let's say it's Б) and feed it through the loop you've just created by pulling it to the left. The loop should close around it.

AD

Ensure the cord is fully fed through, with the rough sides still facing out. The left cord (А) should now be over Б, and the loop should be on the right.

Building the Knot

You've created the foundation of your knot. Now, repeat the process to build it up.

Remember, you're working from left to right. Maintain this direction as you create each new loop, and feed the other cord through it.

Repeat the Process

Make another loop on the left cord (А), this time by lifting it over the right cord (Б). Feed the right cord through this new loop.

Now, alternate between making loops on each cord and feeding the other cord through them, always ensure the rough sides are facing out. Continue the process until you reach your desired pull length. This could take some patience, but the results are worth it!

Finishing the Knot

As you approach the end, you'll notice the cord sections lengthening. This is normal. Keep going until you reach the zipper channel. Once you do:

1. trim the excess paracord
2. melt the ends with your lighter or matches to prevent fraying
3. pull your new paracord zipper pull through the zipper channel
4. secure it by tying a knot on the other side and trimming any excess cord.

Congratulations! You've just made a functional and stylish paracord zipper pull. Display it with pride, and rest assured, you've got a survival tool tucked into your wardrobe. Plus, it's a great conversation starter. Happy creating, and happy exploring!

AD