how to load filament into ender 3

How to Load Filament Into Ender 3: A Step-by-Step Guide

By John Anderson
AD

Loading filament into your Ender 3 3D printer may seem daunting at first, but with the right steps, it's a breeze. Proper filament loading ensures smooth printing and preserves your filament's lifespan. Here's a comprehensive guide to help you master this task.

Before we dive into the steps, ensure your Ender 3 is turned off and the power supply is unplugged. Safety first! Once you're ready, follow these steps to load your filament like a pro.

Preparing the Ender 3

The first step is to prepare your 3D printer for filament loading. Begin by removing any existing filament currently loaded into the printer. This process is called unloading, and it's essential to prevent filament tangling and jamming.

AD
Loading 3D Printer Filament : How to Load Filament into Ender 3 v2
Loading 3D Printer Filament : How to Load Filament into Ender 3 v2
Ender 3 (V2/Pro): How to Change Filament – 3 Easy Steps
Ender 3 (V2/Pro): How to Change Filament – 3 Easy Steps
Loading Filament Section 1.5 featuring the Ender 3
Loading Filament Section 1.5 featuring the Ender 3

Next, ensure your Ender 3's needles and tubes are clean and unobstructed. Clearing any residual filament or dust will ensure a smooth loading process. If necessary, use a filament cleaner or an old toothbrush to gently scrub the interior of the tube and the filament path.

Unloading the Filament

Unloading filament involves retracting the filament and removing it from the printer. Begin by selecting "Preheat" in the printer's menu, then choose the filament you want to unload. Once the filament is heated, manually retract the filament by toggling the filament drive gear, located near the extruder, to the 'retract' position. Slowly pull the filament out of the extruder until it's completely removed.

Simple BLTouch Setup for Ender 3 & Pro
Simple BLTouch Setup for Ender 3 & Pro
How to Change Filament Ender 3: Steps & Advice
How to Change Filament Ender 3: Steps & Advice

Alternatively, you can use firmware commands to unload filament. In Pronterface or OctoPrint, send the following command: "G1 E-5 F100" to retract the filament and "M192 G1 Y35 F100" to unload it completely from the printer.

Priming the Filament

Once your Ender 3 is clean and free of old filament, it's time to prime your new filament. Priming involves feeding new filament into the printer. First, measure your new filament to ensure it's long enough to reach the extruder without kinking. Cut the filament at a 45-degree angle using a pair of scissors or a filiment cutter.

AD

Now, manually turn the filament loading gear to feed the filament into the printer. Keep feeding the filament until it starts to ooze out of the hotend. Be sure not to overfeed, as this can cause a mess and waste filament. Once you see this oozing, stop feeding and proceed to the next section.

Loading the Filament

Loading filament involves correctly setting the filament type and running an initial printing command to extrude the filament into the printer's interior. Begin by selecting your new filament type in the printer's menu. This helps the printer to adjust settings like temperature and extrusion rates accordingly.

Next, run a printing command to load the filament entirely into the printer. Select "Load Filament" in the printer's menu. The printer will automatically extrude the filament, loading it into the printer. Be patient during this process, as it may take several minutes to complete.

AD

Setting Filament Type

Accurately setting the filament type in your Ender 3's menu is crucial for achieving optimal printing results. This setting determines the printer's temperature and extrusion speeds, which are crucial for successful printing. For most filaments, the default settings are adequate. However, for specialty filaments like TPU or PC, you may need to manually adjust the settings.

To set the filament type, first, preheat the printer to the desired temperature. Then, in the printer's menu, select "Change Filament Type." Choose the type of filament you're using, and the printer will adjust its settings accordingly. Once the filament type is set, proceed to load the filament as described above.

Performing the First Print

After successfully loading your filament, it's time to test your work with a test print. Start by selecting "Prepare" in the printer's menu, then choose the filament you just loaded. The printer will heat up to the appropriate temperature for that filament.

AD

Next, load your CAD file and initiate the print. Monitor the printer's progress closely, ensuring that the filament extrudes smoothly and the layer adhesion is strong. If you notice any issues, troubleshoot accordingly, and make any necessary adjustments. Once your test print is complete, your Ender 3 is officially ready to print with your new filament.

Congratulations! You've successfully loaded filament into your Ender 3 and are ready to embark on your next 3D printing adventure. Happy printing, and remember to keep experimenting with different materials and settings to continually improve your skills.

AD