how to install step flashing under existing siding

"How to Install Step Flashing Under Existing Siding"

By William Johnson
AD

Installing step flashing under existing siding might seem Like a daunting task, but with the right tools, materials, and knowledge, you can efficiently improve your home's weather protection. This guide will walk you through the process, ensuring a professional outcome that enhances your home's curb appeal and safety.

Before we dive into the steps, it's crucial to understand what step flashing is and why it's important. Step flashing is a type of flashing used where walls step down, typically at eaves, dormers, or bay windows. It helps to direct water away from the wall and siding, preventing leaks and water damage. By installing step flashing under existing siding, you're reinforcing your home's fortifications against the elements, ensuring longevity and protecting your investment.

Gathering Your Materials and Tools

The first step in any project is to ensure you have the right materials and tools. For this task, you'll need:

AD
How To Install Step Flashings
How To Install Step Flashings
How to Install Siding
How to Install Siding
5 Steps for Flashing a Deck Ledger - Fine Homebuilding
5 Steps for Flashing a Deck Ledger - Fine Homebuilding

  • Step flashing
  • Roofing nails
  • Rubber roofing tape
  • Caulk gun and clear silicone
  • Tin snips
  • Utility knife
  • Tape measure
  • Hammer or roofing nailer
  • Safety gear (gloves, goggles, ear protection)

8.5K views · 8.5K reactions | Next week I’ll be resuming the framing of this small deck/landing and stairs, but this landing technically started last year when I installed and flashed this ledger board against the house. Proper flashing is key. It’s worth noting the ledger flashing is galvanized steel, not aluminum. You wouldn’t want to install aluminum flashing in contact with treated lumber. #framing #deck #carpenter #flashing #siding | Justin Metzler | Facebook
8.5K views · 8.5K reactions | Next week I’ll be resuming the framing of this small deck/landing and stairs, but this landing technically started last year when I installed and flashed this ledger board against the house. Proper flashing is key. It’s worth noting the ledger flashing is galvanized steel, not aluminum. You wouldn’t want to install aluminum flashing in contact with treated lumber. #framing #deck #carpenter #flashing #siding | Justin Metzler | Facebook
a wooden shelf with three compartments attached to the side of a house that has siding on it
a wooden shelf with three compartments attached to the side of a house that has siding on it

Measuring and Planning

Before you start, measure the area where you'll be installing the step flashing. This will help you determine how many pieces of flashing you'll need. Typically, step flashing is placed every 6 to 12 inches apart, so plan accordingly.

Also, familiarize yourself with the area's layout. Identify where the walls step down and any potential obstacles or hazards.

AD

Safety First

Working on a roof can be dangerous, so safety should always be your top priority. Wear non-slip shoes, a safety harness if necessary, and keep your work area clear. Always have someone on the ground, spotting you and ready to assist if needed.

Additionally, it's a good idea to check the weather forecast. Avoid working on a rainy day, and be cautious of high winds and lightning.

Removing Existing Siding (if necessary)

If the existing siding needs to be removed to access the fascia or wall, proceed with caution. You don't want to cause unnecessary damage or create more work for yourself later.

AD

Instead of ripping off the siding, carefully cut it away from the wall in small sections. Use a utility knife to score the seams, then use a flat pry bar to gently pry off the panels. This should allow you to work without compromising the integrity of the existing siding.

Inspecting the Area

Once the siding is removed, inspect the area where the step flashing will be installed. Check for any signs of rot, damage, or pests. If you find any issues, address them before proceeding.

Also, ensure that the area is clean and dry. Any dirt, debris, or moisture can compromise the adhesion of the flashing and facilitate rusting or mold growth.

AD

Installing the Step Flashing

Begin by cutting the step flashing to size. Each piece should be long enough to extend up the shingle on the row above and down the siding on the wall below. Use tin snips to make straight, even cuts. Typically, each piece is about 12 inches long.

Starting at the bottom, nail the first piece of flashing to the fascia, ensuring it overlaps the edge of the shingle below. The bottom flange should extend down the wall, while the top flange lies flat against the shingle. The bottom corner of the flashing should be positioned just below the bottom edge of the shingle.

Caulking and Sealing

After all the flashing is installed, it's time to caulk and seal the seams. This helps to ensure a water-tight barrier and protects the step flashing from the elements.

Using a clear silicone caulk, apply a thin bead along each seam where the flashing overlaps. Use a caulk gun with a fine-tip nozzle to ensure precision and minimal waste. Smooth the caulk with your finger, wiping any excess onto a paper towel.

Installing Counter Flashing

Counter flashing is the final step in the installation process. It's a strip of metal that's inserted into a horizontal groove cut into the mortar joints of brick or block walls. This helps to direct water away from the wall and adds an extra layer of protection.

Use a masonry bit to drill holes into the mortar joints where you'll install the counter flashing. Make sure the holes are deep enough to accommodate the flashing and leave about an inch of material above the surrounding surface.

Insert the counter flashing into the holes, tapping it firmly into place with a hammer. Ensure it's level and flush with the wall's surface. Apply a bead of caulk around the base of the flashing to seal it and prevent water from penetrating behind it.

Reattaching the Siding

Once the step flashing and counter flashing are installed and sealed, it's time to reattach the existing siding. If you removed any siding, carefully reinstall the panels, ensuring they're secure and properly fitted.

Caulk any gaps or seams where the siding meets the wall or step flashing. This will help to prevent water from getting behind the siding and causing damage.

Congratulations! You've successfully installed step flashing under existing siding, enhancing your home's weather protection and enhancing its longevity. With proper maintenance and care, this installation will provide years of service, protecting your home from the harshest elements. Regularly inspect your roof and siding for any signs of wear or damage, and address any issues promptly to ensure your hard work stands the test of time.

AD