how to install rear windshield

Step-by-Step Guide: How to Install Rear Windshield

By Christopher Jones
AD

Installing a rear windshield on your vehicle might seem daunting, but with the right steps and patience, it's a task you can accomplish yourself. This guide will walk you through the process, including gathering materials, preparing your car, removing the old windshield, and finally, installing the new one. Let's dive right in.

Before we start, remember that this is a time-consuming process that requires careful attention to detail. Always prioritize safety by wearing protective gear and ensuring your workspace is clean and well-lit. If you're uncomfortable with any part of the process, don't hesitate to consult a professional.

Gathering Materials and Preparation

First, make sure you have all the necessary tools and materials. You'll need a box cutter or utility knife, a razor blade, isopropyl alcohol, a scraper, a chisel, a screwdriver, gloves, safety glasses, and a new rear windshield, of course.

AD
How To Install a Windshield the
How To Install a Windshield the
HOW TO INSTALL A WINDSHIELD BANNER... THE RIGHT WAY!
HOW TO INSTALL A WINDSHIELD BANNER... THE RIGHT WAY!
3 STEPS TO INSTALL SUPERATV’S SLIDING REAR WINDSHIELD ON THE POLARIS GENERAL XP 1000
3 STEPS TO INSTALL SUPERATV’S SLIDING REAR WINDSHIELD ON THE POLARIS GENERAL XP 1000

Next, prepare your car. Park it in a cool, dry, well-lit area. Lay a drop cloth on the ground to protect your paint and make cleanup easier. Clear the surrounding area of any obstacles that might get in the way during the installation process.

Removing the Old Windshield

Start by removing the molding around the windshield. Use a box cutter or utility knife to cut through any sealant or adhesive holding it in place. Then, carefully pry it off using a flathead screwdriver. If it's stuck, use a chisel to gently tap it loose.

Back Windshield Replacement
Back Windshield Replacement
How to install a vinyl windshield sun visor banner window strip
How to install a vinyl windshield sun visor banner window strip

With the molding removed, you should see the old windshield's edge. Use a razor blade to carefully score around the windshield, cutting through any remaining adhesive. This will make it easier to pry off. Use the chisel and screwdriver to carefully pry up one corner of the windshield. Once you've got a starting point, you can usually just pull the rest of the windshield out.

Preparing the Windshield Area

Before installing the new windshield, you need to clean the area. Use isopropyl alcohol and a scraper to remove any remaining adhesive or old sealant. Be thorough; any debris or leftover adhesive could compromise the new seal.

AD

Check the condition of the existing rear windshield wiper mechanism. If it's worn out or damaged, replace it before installing the new windshield. Also, inspect the pinch welds - the metal edges around the windshield area. If they're damaged, they'll need to be repaired or replaced.

Installing the New Rear Windshield

With the area clean and any necessary repairs made, it's time to install the new rear windshield. Start by laying out your new windshield and aligning it with the car's body. The sides should fit neatly against the pinch welds, and the top should line up with the roof's edge.

Don't apply any adhesive yet. Instead, use painter's tape to temporarily hold the windshield in place. This gives you a chance to ensure it's properly aligned before making a permanent bond. Walk around the car to check the alignment from all angles.

AD

Applying the Adhesive

Once you're sure the windshield is aligned correctly, start applying the adhesive. Many rear windshields come with pre-applied adhesive, which simplifies the process. If yours doesn't, use a professional automotive adhesive according to the manufacturer's instructions.

Apply the adhesive around the perimeter of the windshield, leaving a small gap at each corner. This allows any excess adhesive to escape as you press the windshield into place. Work quickly but carefully; most adhesives set up relatively fast.

Installing the Windshield

With the adhesive applied, carefully lower the windshield into place. Press it firmly against the tape, distributing even pressure across the surface. Hold it in place for the time specified in the adhesive manufacturer's instructions, usually a few minutes.

AD

After the initial set time, remove the tape. Check the adhesion. If any areas are lifting, you may need to apply more adhesive and hold the windshield in place for a longer period. Always follow the adhesive manufacturer's instructions for the best results.

Finally, let the adhesive cure completely before exposing it to water or extreme temperatures. This might take a few days. Once the adhesive is fully cured, you can replace the windshield molding and enjoy the peace of mind that comes with a securely installed rear windshield.

AD