how to install outlet behind tv

Easy DIY: How to Install an Outlet Behind Your TV

By Mark Robinson
AD

Installing an outlet behind your TV might seem like a complex task, but with the right steps and a little patience, it's an achievable DIY project. You'll enhance your space's aesthetics, manage your cables safely, and boost your TV's performance. Let's dive into the process.

Before we start, ensure you have the necessary tools: a stud finder, drill, SafetyFirst electrical box, Romex non-metallic (NM) cable, cable clamp, diagonal pliers, wire stripper, screwdriver, and insulated glasses. Always remember to turn off power at the circuit breaker before starting.

Preparation and Planning

Planning is crucial to ensure a smooth installation. First, decide on the outlet's location. It should be near your TV and avoid obstacles like walls, windows, and doors. Then, configure your wall layout to avoid drilling into studs or pipes.

AD
How to Add an Electrical Outlet for a Wall Mounted TV
How to Add an Electrical Outlet for a Wall Mounted TV
How to Add an Electrical Outlet for a Wall Mounted TV
How to Add an Electrical Outlet for a Wall Mounted TV
2M views · 9.5K reactions | Relocated an outlet doesn't have to be hard. I will demonstrate a few tips to ensure you keep this only an electrical project and stay away from drywall repair and painting. | Everyday Home Repairs
2M views · 9.5K reactions | Relocated an outlet doesn't have to be hard. I will demonstrate a few tips to ensure you keep this only an electrical project and stay away from drywall repair and painting. | Everyday Home Repairs

Grab your stud finder to locate the studs, mark them with a pencil, and plot your outlet's location. Ensure it's at least 1.5" away from the nearest stud to accommodate the electrical box and keep it secure.

Running the Cable

Now, it's time to run the NM cable from your existing power source to the new outlet location. The cable should be at least 14 AWG, rated for 15A, and 12/2 NM for a standard household outlet. Remember, the cable must be long enough to reach both ends and make proper connections.

a man is holding a pair of scissors in front of a wall mounted electrical outlet
a man is holding a pair of scissors in front of a wall mounted electrical outlet
Cheap Ways to Hide TV Cords & Outlets That Actually Look Good
Cheap Ways to Hide TV Cords & Outlets That Actually Look Good

Fish the Cable

Start by making a small hole in the existing outlet's wall plate. Then, carefully fish the NM cable through the wall using a fish tape or a coat hanger. Ensure the cable is secure and follows a straight line to avoid tempting fate with those in the attic or basement.

Once you've reached the new outlet location, mark the spot, and carefully cut a hole slightly smaller than the cable's diameter. Pull the cable through until you have enough to work with - at least 6" - on both sides.

AD

Secure the Cable

With the cable pulled through, it's time to secure it in place. Use a cable clamp at both ends of the run - one at the existing outlet and another just above the new outlet location. This ensures the cable won't shift around in the wall, causing unnecessary wear or damage. To install the clamp, simply drill a small hole into the stud, slip the clamp onto the cable, and secure it with the provided screws.

Now, thread your NM cable through the SafetyFirst electrical box. Ensure the wires are pulled through cleanly and not too tightly, as this can damage the insulation.

Installing the Outlet Box

Next, install the SafetyFirst electrical box. The box should have a knockout panel on all four sides, allowing for flexible cable runs. Before securing the box, ensure the power is still turned off at the circuit breaker.

AD

Secure the Box

Hold the box against the wall and mark the screw holes. Drill pilot holes, ensuring you're not drilling through any wires or pipes. Screw the box firmly against the wall, securing it with two screws. Make sure it's snug and level.

The box should sit flush with the wall, with the cable running through it snugly but not tightly. If the cable's too loose, you can pull it taut and loop it inside the box to tighten it.

Move the Power

Now, connect the NM cable to the existing circuit. Strip about 2" of insulation from the black (hot), white (neutral), and ground wires. Use a wire stripper to carefully remove the insulation without nicking the copper wire underneath.

AD

Twist the ends of each wire with wire nuts, connecting like wires: black to black, white to white, and ground to ground. Then, twist the ground wires together again and insert them into the green grounding bar on the existing outlet's terminals.

Finishing Up

Finally, it's time to install the new wall plate and test your new outlet. Snap the plate into the electrical box, ensuring it's secure and squared up with the wall.

Turn the power back on at the circuit breaker and test your new outlet with a multi-meter to ensure it's wired correctly. If everything's working as it should, pat yourself on the back - you've just installed an outlet behind your TV!

Don't forget to clean up your workspace and double-check that all tools are properly stored. Who knows what the future holds, but with your newfound skills, you might just tackle another DIY project soon.

AD