how to install ground bar in subpanel

Step-by-Step: Installing a Ground Bar in a Subpanel

By Joseph Martinez
AD

Installing a ground bar in a subpanel is a crucial safety measure that every homeowner or electrician should know. A ground bar, also known as an equipment grounding conductor (EGC), ensures electrical safety by providing a low-impedance path for fault currents to flow in case of a short circuit. This article will guide you through the process of installing a ground bar in a subpanel, step by step.

Before we dive into the installation process, let's familiarize ourselves with the necessary tools and materials. You will need a ground bar (ensure it's the right size for your subpanel), several 10-32 or 1/4-20 grounding screws, a screwdriver, a wire stripper, and, of course, electrical gloves and safety glasses for protection.

Preparation and Safety Measures

Before starting any electrical work, ensure you have shut off the main electrical supply to the subpanel. This is crucial to prevent electrocution. Use a voltage tester to confirm that the power is indeed off before proceeding.

AD
How To Install a Ground Bar In a Sub Panel or Main Load Center
How To Install a Ground Bar In a Sub Panel or Main Load Center
How to properly ground a subpanel in detached building?
How to properly ground a subpanel in detached building?
a person is working on an electrical panel
a person is working on an electrical panel

Always follow the National Electrical Code (NEC) guidelines and local electrical codes when performing any electrical work. If you're unsure about any aspect of the process, consult a certified electrician.

Understanding Your Subpanel

Subpanels come in various sizes and configurations. The size of the subpanel determines the number of circuits it can handle. For the purpose of this article, we'll assume you have a 200-240V, 12-30-circuit subpanel with a main breaker.

Master Sub Panel Installation: Learn How To Install A Sub Panel
Master Sub Panel Installation: Learn How To Install A Sub Panel
an electrical panel with multiple wires in it
an electrical panel with multiple wires in it

Locate the ground bar in your subpanel. Modern subpanels typically have a ground bar, usually located at the bottom of the panel. If your subpanel doesn't have a ground bar, you'll need to install one as part of this process. For this guide, we'll assume you're installing a new ground bar.

Installing the Ground Bar

Start by removing the necessary knockouts from the subpanel's enclosure. You'll need one knockout near the bottom of the panel for the grounding wire and one near the top for the bonding wire.

AD

лыхший. Use a single-ray set or a hammer to gently tap the knockouts out of the subpanel. Be careful not to damage the panel or the knockouts. Once the knockouts are removed, you can move on to running the grounding wires.

Running the Grounding Wires

The grounding electrode conductor (GEC), also known as the ground wire, connects the subpanel to the grounding electrode, usually a metal rod or a cold water pipe. The grounding electrode conductor must be run in accordance with local electrical codes and the NEC.

For this guide, we'll assume you're running the GEC from a UF (Underground Feeder) cable connected to a grounding electrode. The GEC should be made of solid copper wire and should be at least as large as the gene conductor serviced by the subpanel, up to a maximum of #4 AWG.

AD

Running the GEC

Using the wire stripper, strip enough insulation from the GEC to allow for at least three wire diameters of straight, exposed conductor. Twist the exposed conductor back on itself to prevent it from unraveling.

Connect the GEC to the grounding electrode using an appropriate grounding clamp or lug. Ensure the connection is tight and clean, with no opportunity for corrosion. Once the GEC is securely attached to the grounding electrode, it's time to connect it to the subpanel.

Connecting the GEC to the Subpanel

Run the GEC through the knockout you've prepared at the bottom of the subpanel. Connect the GEC to the ground bus bar in the subpanel using an appropriate sized screw. This screw should be made of stainless steel or another corrosion-resistant material. Tighten the screw securely, but be careful not to over-tighten and strip the screw.

AD

The ground wire is now connected to the subpanel, but the bonding conductor must still be installed. The bonding conductor ensures that all metallic parts of the subpanel are at the same potential, which is a critical safety measure.

Running the Bonding Conductor

The bonding conductor is typically a #12 AWG copper wire, but its size can vary depending on local codes. The bonding conductor runs from the bonding terminal in the main panel to the bonding terminal in the subpanel.

For this guide, we'll assume you're running the bonding conductor from the main service panel to a subpanel that's a few feet away. Drill a hole in the wall large enough to accommodate the bonding conductor and the appropriate-sized conduit. Pull the bonding conductor through the conduit and connect it to the bonding terminal in the subpanel using an appropriate sized screw.

Testing the Ground Bar

Once both the GEC and the bonding conductor are securely connected to the subpanel, it's time to test your handiwork. Use a voltmeter or an ohmmeter to confirm that the ground bus bar in the subpanel is solidly grounded. If the ground is solid, the reading should be 0 Ohms. If the ground is not solid, double-check your connections and ensure that all grounding clamps, lugs, and screws are tight and clean.

The final step in this process is to replace the subpanel's cover and restore power to the subpanel. Be sure to inspect the entire installation before turning the main breaker back on. Always double-check your work before powering up a new electrical installation.

Installing a ground bar in a subpanel is a straightforward process that can significantly improve the safety of your electrical system. By providing a low-impedance path for fault currents, the ground bar can prevent electrical fires and shock hazards. If you're unsure about any aspect of the installation process, consult a certified electrician to ensure your electrical system is safe and up to code. Happy installing!

AD