How to Install Ecobee PEEK
The Ecobee PEK (Power Extender Kit) is an essential component for installing an Ecobee thermostat, enabling it to power devices with up to 200 VA. This guide will walk you through a step-by-step process of installing the Ecobee PEK, ensuring your system is set up correctly for optimal performance.
Before you proceed, ensure you have the following items on hand: your Ecobee thermostat, the PEK (Power Extender Kit), a screwdriver, and a wire stripper. Familiarize yourself with the process and the location of your home's wiring before starting. If you're unsure, consult a professional.
Understanding Your Home's Wiring
Begin by understanding your home's wiring. Most homes have 24V wires (R, C, W, Y) connected to the HVAC system. Located behind your current thermostat, these wires will be used to connect your new Ecobee thermostat and PEK.
Use the following table to identify your wires:
| Wire Color | Function |
|---|---|
| R (Red) | 24V Power (Hot) |
| C (Common) | 24V Return (Neutral) |
| W (White) | Heat Pump or Heat (Stage 2) or Emergency Heat |
| Y (Yellow) | Cooling (Stage 2) |
| G (Green) | Fan (Stage 2) |
Connecting the Ecobee Power Extender Kit (PEK)
The PEK acts as a transformer, stepping up the voltage to power the Ecobee thermostat. Connect the PEK first, then your thermostat.
1. Strip about ¾" of insulation from the wiring using the wire stripper. Twist the exposed copper ends.
2. Connect the following wires to the PEK:
R to RCC to CC
Any additional wires (W, Y, G) should be connected to the corresponding colored terminals.
Note: Some terminals may be labeled with both the color and the function. Always use the function label if there are multiple options.
Connecting the Ecobee Thermostat
Once your PEK is connected, it's time to wire your Ecobee thermostat.
1. Using the same wiring rules as the PEK, connect the remaining ends of the wires from your home's HVAC system to the corresponding terminals on your Ecobee thermostat.
2. Ensure the 'G' terminal is connected if you have a fan (G2) or a humidifier (G). If these are not present, you can use 'G' for the fan (G1) or leave it unconnected.
Installing the Ecobee Thermostat and PEK
Now that your thermostat and PEK are wired, it's time for the physical installation.
1. Turn off the power to your HVAC system at your main electrical panel. Verify the power is off using a non-contact voltage tester.
Mounting the PEK
The PEK should be mounted near your HVAC equipment near the existing wiring. This keeps the thermostat wires short and prevents degradation in signal.
1. Using the mounting template provided with your PEK, mark the drill points on the wall.
2. Drill holes and secure the PEK mounting bracket to the wall.
3. Route the wiring through the provided plastic conduit and connect the PEK to the bracket.
4. Secure the PEK to the bracket using the provided screws.
Mounting the Ecobee Thermostat
The Ecobee thermostat should be mounted near the PEK, typically on an indoor wall close to your HVAC equipment.
1. Using the provided mounting hardware, attach the wall plate to the desired location.
2. Route the wiring through the wall plate and connect it to your Ecobee thermostat.
3. Secure the thermostat to the wall plate using the provided screws.
4. Power up your HVAC system at the main electrical panel.
5. Follow the on-screen instructions to complete the setup process on your Ecobee thermostat.
Congratulations! You have successfully installed your Ecobee thermostat and Power Extender Kit. Enjoy the convenience and energy savings brought by this smart HVAC control system.