How to Install Crochet Braids: Step-by-Step Guide
Embracing the world of hair extensions is an exciting journey, and one of the most rewarding DIY methods is installing crochet braids. This versatile technique allows you to add fullness and length to your hair while providing low-manipulation styling. So, if you're ready to enhance your hair's volume and length without compromising its health, let's dive into a step-by-step guide on how to install crochet braids like a pro.
Before you start, gather all the necessary tools: human hair crochet braids, crochet needle, hair comb, rat-tail comb, ratchet clamps, perm rods (optional), a base coat product like argan oil or shea butter, and a hair extension brush. Now, let's meticulously walk through each section of this process.
Preparation
The key to a successful crochet braid installation is prepping your hair and tools correctly. Start by shampooing your hair and gently detangling it using a wide-tooth comb. Remember, your hair should be detangled but not fully stretched out, as this could cause shedding during the installation process.
Next, lightly oil your scalp and hair with a base coat product to eliminate friction and help prevent tangling. You can use products like argan oil, shea butter, or a moisturizing leave-in conditioner. This step also helps create a protective layer between your hair and the braids, promoting hair health during the install.
Sectioning Your Hair
Once your hair is well-coated, start sectioning it by parting it into four equal sections – two in the front and two at the back. This will make it easier to manage while installing the crochet braids.Secure each section with a ratchet clamp to keep them in place and avoid tangling.
First, focus on the back sections. Use the rat-tail comb to create a narrow parting at the nape of your neck. This will be your starting point for installing the crochet braids. The smaller the parting, the more secure your installation will be.
Creating the Feed-in Braid
The feed-in braid is crucial as it provides a solid base for the crochet braids to sit on. Use a small section of hair from the nape of your neck and create a standard three-strand braid, adding a small amount of hair from both sides as you go down. Remember to keep the braid as close to your scalp as possible to create a secure foundation.
After about 2-3 inches, stop adding hair from the sides and continue braiding the remaining hair only. This ensures that the braid tapers off at the end, creating a seamless transition for the crochet braids. Secure the end of the braid with a small ponytail holder or metallic hair tie.
Installing the Crochet Braids
Now that you have created a solid foundation, it's time to start installing the crochet braids. Take one of the human hair crochet braids and separate the kinky curl or straight tip at the end into three sections. Feed these sections into the loop of your crochet needle, making sure to keep them quaisin.
Insert the crochet needle under the first feed-in braid, about 1-2 inches away from the starting point. Pull the needle all the way through, making sure to loop the hair up as you pull. This will create a small "lark's head" knot. Make sure the knot is snug against your scalp for maximum hold.
Crocheting the Braids
With the first crochet braid attached, take a small section of your natural hair from the left side of your feed-in braid and insert it into the loop of your crochet needle, following it with a small section of the crochet braid. Pull the needle through the existing "lark's head" knot, creating a new loop and pulling both sections of hair through.
Repeat this process, alternating between your natural hair and the crochet braid, pulling them both through the loops you've created. Make sure to keep your tension consistent and pull the hair taut against your scalp to ensure a secure installation. Continue this process, working your way up the nape of your neck.
Once you reach the top of your head, carefully raster your braids out using a wide-tooth comb or your fingers to disguise the crochet braids and create a seamless, natural look. If you find that some of your crochet braids are too short, you can use perm rods to create loose curls, which will help hide the ends.
Finishing the Installation
After installing the crochet braids on both back sections, move on to the front sections. Repeat the same process, creating feed-in braids and installing the crochet braids, making sure to keep your tension consistent and blend the braids with your natural hair.
As you reach the top of your head, use a headband or hairnet to secure the loose ends of your crochet braids, keeping them in place while you finish the installation. Once all the crochet braids are in, use a wide-tooth comb or your fingers to gently raster the braids, creating a natural look that blends seamlessly with your natural hair.
Finally, use a hair extension brush to gently detangle the ends of your crochet braids, ensuring they fall smoothly and naturally. Don't forget to lightly oil your scalp and hair to keep it moisturized and nourished throughout the installation process.
Post-installation, you can style your crochet braids just like natural hair. Experiment with different hairstyles, such as updos, side-parted looks, or beachy waves. Remember, proper maintenance, like gently detangling the braids and keeping the scalp clean, will prolong the life of your crochet braids and ensure a seamless, natural look.
Embracing the art of crochet braiding is a rewarding journey that allows you to express your creativity while enhancing your hair's appearance. With this comprehensive guide, you're now equipped to install crochet braids like a pro. Happy styling, and may this newfound skill bring you the confidence and versatility you deserve in your hair journey!