how to install burton channel bindings

Burton Channel Bindings: Easy Step-by-Step Installation Guide

By Robert Williams
AD

So, you've decided to up your snowboarding game with a pair of Burton channel bindings? Great choice! These bindings not only provide superior performance but also offer a wide range of adjustability to suit your style. However, installing them can seem daunting if you've never done it before. Fret not, we're here to guide you through the process with this step-by-step guide. Let's get started!

Before we dive in, there are a few tools and materials you'll need: your Burton channel bindings, a Phillips #2 screwdriver, an 8mm hex key, and a maltese wrench. You'll also want to have your snowboard, channel mounting hardware, and hex nuts and mounting washers on hand. Now, let's break down the installation process.

Preparation and Safety

Before you begin, ensure you're working in a well-lit, stable surface. It's also a good idea to lay out all your tools and materials within reach. Safety first, so remove or disable any power tools before starting.

AD
| How To Set Up Burton EST Bindings On The Channel System
| How To Set Up Burton EST Bindings On The Channel System
Installing Burton Re:Flex Bindings on Channel Boards | Snowboarding Profiles
Installing Burton Re:Flex Bindings on Channel Boards | Snowboarding Profiles
Burton Snowboards
Burton Snowboards

Inspect your channel bindings, hardware, and snowboard for any damage. Check that all components are accounted for and in good working condition. If anything is questionable, it's better to replace it before proceeding to avoid any accidents on the mountain.

Mounting the Bindings

Burton channel bindings come with a liberal amount of hardware. For this guide, we'll focus on the most common setup, the 4x4 pattern. If your board has a specialized mounting pattern, consult Burton's specific installation instructions.

Burton Cartel Bindings Review
Burton Cartel Bindings Review
| How to Choose Your Snowboard Bindings
| How to Choose Your Snowboard Bindings

Marking the Mounting Points

Start by placing your bindings on the snowboard, centered over the inserts. Align the toepiece with the toe edge of the board and the heelcup with the heel edge. Use a marker or a pencil to trace around the mounting baseplate.

You'll also need to mark the four corner holes of the baseplate. Do this by placing the baseplate flush against the board and gently pressing on each corner. Make small marks where the holes meet the board's surface.

AD

Drilling the Inserts

Using your 8mm hex key, tighten the inserts onto your Burton channel mount, leaving the Allen bolts loose. Place these assemblies onto your marked points and secure them with the provided 8mm hex bolts. Be sure not to overtighten; you should be able to wiggle the assembly slightly.

Using an 8mm drill bit, carefully drill through the Allen bolts and into the board. Be sure to keep the drill perpendicular to the board's surface to avoid any warping. Once you've drilled all four holes, you're ready to install the bindings.

Installing the Bindings

This is where the Burton channel system truly shines. The channel allows for infinite adjustment of the bindings, making it easy to fine-tune your stance. Here's how to install them:

AD

Installing the Baseplate

Place the baseplate onto the channel mount, sliding it into the channel until it stops against the heelcup insert. Secure the baseplate to the mount using the provided screws and a Phillips #2 screwdriver. Tighten until snug, but avoid overtightening.

Next, install the heelcup by sliding it into the channel and securing it with the provided screw. Ensure the heelcup is flush against the heel of the baseplate. Now's the time to start fine-tuning your stance width and angle.

Installing the Toepiece

The toepiece can be a bit tricky, so take your time. Align it with the front of the baseplate and slide it into the channel. Push it all the way forward until it stops. Secure it with the provided screw.

AD

You can now start playing with your stance width and angle. The channel allows for a wide range of adjustment, so don't be afraid to experiment. Once you've found your perfect setup, tighten the hex bolts on the channel mount to lock everything in place.

Congratulations! You've successfully installed your Burton channel bindings. Now all that's left is to hit the slopes and put them through their paces. Remember, the first few runs may take some getting used to, but with Burton channel bindings, you can fine-tune until you're comfortable. So, get out there and shred! Safe riding!

AD