how to install a header in a load bearing wall

Step-by-Step: Install a Header in a Load Bearing Wall

By Christopher Moore
AD

Installing a header in a load bearing wall might seem like a daunting task, but with the right steps and precautions, it's definitely doable. Not only will a header improve the safety and structural integrity of your wall, but it will also create a beautiful architectural feature. Let's embark on this home improvement journey together.

Before we delve into the process, let's ensure you understand the importance of a header in a load bearing wall. When you remove a wall, you create a Unsupported span that needs to be closed properly. This is where the header comes in. It helps to transfer the load from the wall above to the supporting beams, preventing any structural damage. Now that we're on the same page, let's get started!

Gathering Your Tools and Materials

Before you begin, make sure you have all the necessary tools and materials. Cutting corners with this part could lead to frustration or even dangerous situations. Here's what you'll need:

AD
How To Remove a Wall and Install a Header - Without Bringing Down The House!
How To Remove a Wall and Install a Header - Without Bringing Down The House!
two men working on the framing of a house
two men working on the framing of a house
40 Load Bearing Wall Ideas for Kitchens
40 Load Bearing Wall Ideas for Kitchens

  • Tape measure
  • Circular saw or handsaw
  • Hammer
  • Claw hammer or pry bar
  • Level
  • 2x10 or 2x12 boards for the header (size depends on wall height)
  • 1/2" or 3/4" adjustable tie straps
  • 3" or 3-1/4" screws
  • Construction adhesive

How to Install a Load-Bearing Beam
How to Install a Load-Bearing Beam
Taking Out A Load Bearing Wall? Read This First.
Taking Out A Load Bearing Wall? Read This First.

Planning and Measuring

Accuracy is key in this step. You're not just measuring the width of the opening but also ensuring the header is long enough to span the entire opening plus 2" on each side. This overhang is what will be anchored into the framing on either side. Don't forget to account for the thickness of the header when measuring the height of your opening.

Mark the header's position on the existing wall using your level. Draw lines from the top corner of the opening to the bottom corner on both sides. This will serve as your guide when installing the header.

AD

Removing the Old Wall

Carefully remove the existing wall, starting from one corner, marking any location of electrical or plumbing lines as you work. This will help you navigate the new opening safely. Keep the area well-lit and wear appropriate safety gear. Once the wall is removed, use your level to ensure the header will fit perfectly.

With the old wall out of the way, you can now focus on framing the new header. Start by cutting your header boards to size using your circular saw. Ensure you cut them slightly longer than the measured opening to give you room for error.

Installing the Header

Now that you have your boards cut, it's time to install the header. Begin by applying construction adhesive along one edge of the header board. This will provide extra support and prevent the header from separating.

AD

Start at one end of the opening and lift the header board into place. Ensure it's level and properly aligned with the previously drawn lines. Use your claw hammer or pry bar to provide additional support if needed. Once the header is securely in place, have a helper hold it there while you secure it using the 3" or 3-1/4" screws. Space them evenly along the length of the header.

Attaching Tie Straps

After the header is securely attached, it's time to install the tie straps. These will help to secure the header to the existing framing. Measure and mark where you'll attach the tie straps, ensuring they're perpendicular to the header board and parallel to each other. Use your level to ensure accuracy.

Drill pilot holes into the existing framing and the header board. Align the tie straps over the pilot holes and attach them using 3" or 3-1/4" screws. Ensure they're taught, providing ample support to the header.

AD

Closing the Header

With the header securely in place and the tie straps attached, you can now fill in the space above the header with framing lumber. This will create a finished look and prevent anything from falling through the opening. Start by attaching a 2x4 board to the top of the header, followed by 2x4 studs spaced evenly along the length of the opening.

Once your framing is complete, you can install drywall, ensuring it's properly secured to the studs. Remember to use drywall screws that are long enough to penetrate the header board and ensure a strong connection.

Congratulations! You've successfully installed a header in a load bearing wall. This impressive DIY project has not only improved the structural integrity of your home but also added value to your property. Don't forget to share your success story with others and Enjoy your beautiful, safe new space!

AD