how to install a double pole switch

How to Install a Double Pole Switch: Step-by-Step Guide

By Andrew Robinson
AD

Embarking on a home improvement project can be an exciting yet daunting task. One common upgrade is swapping out a single pole switch for a double pole switch. This upgrade allows you to control two separate lights or sets of lights from a single switch, providing added convenience and aesthetics to your living space.

Before you start, ensure you have the right tools and knowledge. Double pole switches are designed to handle two separate circuits, making them ideal for controlling two lights at once, such as in a bathroom with separate vanity and shower lights. Let's guide you through the step-by-step process of installing a double pole switch.

Preparation and Understanding Your Switch

Before you start, ensure you understand the difference between single pole and double pole switches. As the name suggests, a double pole switch controls two separate circuits. They have four terminals: two line terminals and two load terminals, each for the respective circuit.

AD
CLICK 20A Double Pole Switch Installation Guide
CLICK 20A Double Pole Switch Installation Guide
Home
Home
three way switch wiring with two lights and one light on the other side, in parallel to
three way switch wiring with two lights and one light on the other side, in parallel to

Next, prepare your tools. You'll need a screwdriver, wire strippers, voltage tester, and, of course, your double pole switch. Always prioritize safety by turning off the power at the circuit breaker and using a voltage tester to double-check that the wires are indeed dead.

Removing the Old Switch

Disconnecting the Wires

Begin by unscrewing the switch plate and setting it aside. Then, remove the screws holding the switch to the electrical box. Slowly pull the switch out and identify the black (hot), white (neutral), and green (ground) wires. Using your wire strippers, strip about an inch of insulation from each wire.

Replace 1 Switch with 2: Leviton Combination Device Installation
Replace 1 Switch with 2: Leviton Combination Device Installation
How to Wire Double Switch (2 SP Switched in One unit)
How to Wire Double Switch (2 SP Switched in One unit)

Next, carefully disconnect the wires from the old switch. Black wires are typically attached to the brass-colored screws, while white wires are connected to the silver-colored screws. If you're unsure, consult an experienced electrician or your local building codes to ensure you comply with regulations.

Preparing the Wires for the New Switch

Once the wires are disconnected, use your voltage tester to ensure they're not hot. If the wires are from two separate circuits, they should be completely dead. If not, double-check that you've turned off the correct circuit breakers and that there are no other sources of power connected to these wires.

AD

Now, bend the wires into loops and straighten them slightly. This will make it easier to insert them into the new double pole switch. Ensure all wires remain free of kinks and bends that could cause damage or reduce conductivity.

Installing the Double Pole Switch

Inserting the Wires

Insert the white wires into the silver screw terminals on the double pole switch, ensuring one wire from each circuit goes into its respective terminal. Tighten the screws gently but firmly to secure the wires in place. Keeping the wires neat and organized will help prevent any future issues.

Next, insert the black wires into the brass-colored screw terminals, again ensuring each wire from a separate circuit goes into its respective terminal. Tighten these screws securely as well. The ground wire should be looped around the green terminal, or wrapped around the screw if your switch doesn't have a dedicated ground terminal.

AD

Securing the Switch

Once all wires are secure, gently push the switch back into the electrical box until it's flush with the wall. Ensure no wires are damaged or pinched during this process. Then, replace the switch plate, securing it with screws.

Finally, restore power to the circuit and test your new double pole switch. If everything is working correctly, your two lights should now be controlled by a single switch.

Installing a double pole switch can indeed be a rewarding task, adding both function and style to your home. However, always prioritize safety and, if unsure, don’t hesitate to consult a professional electrician. Happy upgrading!

AD
AD