how to install a double light switch

Step-by-Step: How to Install a Double Light Switch

By Andrew Williams
AD

Installing a double light switch might seem daunting, but with the right steps and careful attention, it's a task well within reach for any homeowner. This guide will walk you through the process, ensuring you understand each step for a safe and successful outcome.

Before you start, make sure you have the necessary tools and materials. You'll need a voltage tester, wire stripper, screwdriver, needlenose pliers, and replacement switches. Always remember to turn off power at your main panel before beginning any electrical work.

Understanding Your Current Switch

Before you remove your current switch, understand its components. A typical single-pole switch has two terminals: one connected to the power source and the other to the light. A double light switch, however, has three terminals: one for power and two for the lights. This small difference impacts how you'll wire your new switch.

AD
How to wire a Double Switch
How to wire a Double Switch
a man standing in front of a wooden door holding a glass container with the text dad advice how to install a dimmer light switch
a man standing in front of a wooden door holding a glass container with the text dad advice how to install a dimmer light switch
How to wire a double switch Combination two switches; double switch. DIY
How to wire a double switch Combination two switches; double switch. DIY

Safety first: Before touching any wires, use your voltage tester to ensure the power is off. Test the wires leading to the switch to confirm there's no power.

Removing the Old Switch

First, remove the switch cover plate and unscrew the switch from its electrical box. There might be a small metal tab at the back of the switch that you need to bend with your needlenose pliers to release it from the box.

How to Wire a Light Switch and Outlet Combo | 6 Easy Ways (2026)
How to Wire a Light Switch and Outlet Combo | 6 Easy Ways (2026)
How to Wire Double Switch? 2-Gang, 1-Way Switch - IEC & NEC
How to Wire Double Switch? 2-Gang, 1-Way Switch - IEC & NEC

Next, remove the two wires connected to the switch. Twist the ends of these wires back into loops to prevent the exposed copper from touching other wires or metal in the box.

Preparing Your Wires

Now, prepare your new double light switch. Strip about 3/4 of an inch of insulation from your wires. If you're using 12-2 or 14-3 non-metallic (NM) cable, you'll have two or three wires inside, respectively. Black and red wires are hot; the white wire is neutral, and the green/bare wire is ground.

AD

Your black or red wire goes to the brass terminal on your new switch. This is your power source wire. The white neutral wire goes to the silver screws on the switch. Finally, the ground wire (green or bare) should be capped and attached to the green ground screw on the switch or, if not present, to the ground screw in the box.

Wiring the New Double Light Switch

Now that your wires are prepared, it's time to connect them to your new switch. Remember, a double light switch has three terminals. Your power source (black or red) goes to the brass terminal. The two neutrals (white) go to the two silver terminals.

Caution: It's tempting to connect the two hot wires (black or red) to the brass terminal. However, this will cause a short circuit, potentially causing a fire. Always follow the correct wiring sequence.

AD

Wiring the First Light

Let's start with the first light. Connect the wire coming from the light fixture to one of the brass terminals on your new switch. This terminal should already have your power source wire connected. Push the wire into the terminal, then tighten the screw to secure it.

Next, connect the neutral wire from the light fixture to the corresponding silver terminal on the switch. Again, push the wire into the terminal and tighten the screw.

Wiring the Second Light

For the second light, follow the same process. Connect its power source wire (black or red) to the remaining brass terminal on the switch. Then, connect its neutral wire to the second silver terminal.

AD

Remember, the ground wires on both lights should be connected together and to the green ground screw on the switch or the ground screw in the box. If your switch or box doesn't have a ground screw, you'll need to use a wire nut to cap and connect the ground wires together.

Finally, carefully tuck all wires back into the electrical box, ensuring none are pinched or compressed. Replace the switch, secure it in the box, and put the cover plate back on. Then, go to your main panel and restore power.

Congratulations! You've successfully installed a double light switch. Always test your work by turning the power back on and flipping the switch to ensure both lights turn on. Regularly testing your electrical work helps maintain the safety of your home.

AD