how to install a brita filter

Step-by-Step Guide to Install Brita Filter: Easy and Fast

By Brian Robinson
AD

Trying to ensure you and your loved ones always have access to fresh, clean water? You've likely heard of Brita filters, which is great, because that's our topic of the day: how to install a Brita filter. Let's dive right in! These handy devices make the process easy, so you can enjoy purified water in no time.

Before we begin, let's quickly recap what you'll get from your Brita filter. Primarily, it removes impurities, such as chlorine, sediment, and microbial cysts, significantly improving both taste and quality. Now, ready to start? Grab your Brita filter, a clean cup, and let's proceed.

Preparing the Brita Filter

You can't begin the installation process without prepping your filter. So, let's.messages" href="https://support.brita.com/all-articles/KB001048 outset with this crucial step.

AD
How to Install Brita Water Filter on Pull Out Faucet
How to Install Brita Water Filter on Pull Out Faucet
The Easy Way to Install Your Water Filter
The Easy Way to Install Your Water Filter
Brita Large Water Filter Pitcher for Tap and Drinking Water
Brita Large Water Filter Pitcher for Tap and Drinking Water

First, take out the filter. It should be wrapped in clear plastic. Carefully unwrap it, being mindful of the water inside - it's not trash, so don't discard it! Maintain the filter's position with the arrows pointing up as you unwrapped it.

Rinsing the Filter

Why should you rinse the filter? Well, it washes away any particulates or activated carbon dust that could affect the water's taste. Here's how:

Instructions on Replacing a Brita Filter Instructions
Instructions on Replacing a Brita Filter Instructions
How to Set Up a Brita Water Filter | Easy Installation Guide
How to Set Up a Brita Water Filter | Easy Installation Guide

Hold the filter under your faucet and run cold water through it for about 15 seconds. You might see the water turn cloudy at first - don't worry, that's normal! Just keep rinsing until the water runs clear.

Re-positioning the Filter

Now, with the filter rinsed, replace it into the filter holder. Ensure the 'A' or '1' - depending on your model - is facing up. This usually aligns with the Brita logo.

AD

Next, twist the filter holder clockwise into the base of your pitcher. You'll hear a click, which indicates it's securely locked in place.

Installing the Filter in Your Pitcher

Congratulations! You've prepped your Brita filter. Now, let's install it in your pitcher for the first time.

Check if your pitcher has a 'FR' (Fsst Resin) and 'DUAL' label. If so, ignore the 'FR' and use only the 'DUAL' filter. Then, follow these steps:

AD

Placing the Filter in the Pitcher

Point the filter holder's arrows to the pitcher's lid and gently lower the filter into the pitcher. The filter should line up with the pitcher's center.

Then, twist the filter into a locked position. You should hear a click once it's secure. Remove the filter by turning it counterclockwise.

Securing the Filter Lid

align="center">Now, replace the lid. Press it down and listen for a click to ensure it's fastened securely.

AD

Congratulations! You've installed your Brita filter. Now, get ready to fill your pitcher for the first time.

Filling the Pitcher for the First Time

Finally, it's time to fill your pitcher and enjoy your fresh, clean water.

Removing the Sticker

Before pouring water into the pitcher, remove the red sticker located on the lid. This indicates the filter is new and ready for use.

Filling and Waiting

Begin filling your pitcher with tap water. Once it's full, let it rest for a few minutes. This will help remove any air in the filter and ensure the water becomes fully filtered.

lavors" href="https://support.brita.com/all-articles/KB001048">enjoy your fresh, clean water! Be sure to discard the filter after replacing it every 40 gallons or two months, or as indicated by the electronic light on some models. Happy hydrating!

AD