how to install a belt on a whirlpool dryer

Step-by-Step Guide to Installing a Belt on a Whirlpool Dryer

By Daniel Thompson
AD

If you're encountering issues with your Whirlpool dryer, such as declining performance or odd noises, check the dryer belt. This crucial component helps your dryer tumble clothes efficiently. Replacing it is simpler than you might think and could save you the cost of a professional repair. Here's a step-by-step guide on how to install a belt on a Whirlpool dryer.

Before we begin, ensure you have the correct Whirlpool dryer belt model that matches your appliance. Also, safety comes first - unplug the dryer from the power source and allow it to cool before starting any work.

Gather Your Materials and Tools

To ensure your task runs smoothly, gather all necessary materials:

AD
How to Replace a Dryer Belt on Whirlpool Models
How to Replace a Dryer Belt on Whirlpool Models
Dryer Belt installation Guide
Dryer Belt installation Guide
DIY Whirlpool/KitchenAid/Maytag Dryer Belt Replacement: Step-by-Step Guide
DIY Whirlpool/KitchenAid/Maytag Dryer Belt Replacement: Step-by-Step Guide
  • New dryer belt (ensure it's the correct model for your Whirlpool dryer)
  • Screwdriver (usually Phillips-headed)
  • Flathead screwdriver
  • Needle-nose pliers
  • Wrench (if removing a seize converter)

Access the Dryer Belt

Begin by removing the screws that secure the back panel of your dryer. This panel can be found at the rear of the appliance. Use your screwdriver to unscrew and remove the panel carefully. Set it aside.

Next, locate the dryer drum. It's the large, circular part of the dryer that trembles when the dryer runs. It's supported by a couple of bolts, typically at the rear. Loosen these bolts using your wrench or screwdriver, and slide the drum forward to expose the belt.

DIY Whirlpool/KitchenAid/Maytag Dryer Belt Replacement: Step-by-Step Guide WP8547168
DIY Whirlpool/KitchenAid/Maytag Dryer Belt Replacement: Step-by-Step Guide WP8547168
How to Replace a Dryer Belt on Whirlpool Models
How to Replace a Dryer Belt on Whirlpool Models

Remove the Old Belt

Using your needle-nose pliers, carefully pull out the old belt from around the dryer's tensioner pulley and idler pulley. You might need to shift the pulleys slightly to free the belt. Once out, discard the old belt.

If you have a seize converter, note its position and gently bend back the tabs securing it. Use your wrench to remove it, and set it aside.

AD

Install the New Belt

Begin installing the new belt by looping it around the idler pulley first, then bring it under the dryer drum. From there, loop it over the tensioner pulley and bring it back towards the drum. Ensure the belt path replicates the old belt's path.

Some dryers may have a specific direction for the belt to travel (found in your dryer's manual). If so, follow that direction during installation.

Tension the New Belt

Now, apply the correct tension to the belt. Begin by pushing the dryer drum back into its original position and partially retighten the bolts securing it.

AD

Next, adjust the tensioner pulley using the pulley's screw. Tighten the screw until the belt develops a slight amount of tension. Be cautious not to overtighten, which can damage your dryer or cause the belt to jump off the pulleys.

Reinstall the Back Panel

With the belt correctly tensioned, it's time to reinstall the back panel of your dryer. Align it with the screws and fasten it securely using your screwdriver.

Lastly, plug your dryer back into the power source and test it by running a short cycle to ensure the belt is working correctly. Your Whirlpool dryer should now be back to tumping clothes efficiently.

AD

Regular maintenance of your Whirlpool dryer, including periodic checks of the dryer belt, can help extend the lifespan of your appliance and prevent unexpected breakages. Keep your user manual handy for specific model assistance, and don't hesitate to contact professional assistance if you face any challenges during this process. Happy DIY repairs!

AD