How to Flush a Navien Tankless Water Heater
A well-maintained Navien tankless water heater can provide your home with an endless supply of hot water. However, like any appliance, it requires proper care to function effectively. Flushing your Navien water heater regularly is crucial to remove any sediment buildup and maintain its efficiency. This comprehensive guide will walk you through the process of flushing your Navien tankless water heater step by step.
Before we dive into the process, it's essential to understand why flushing your water heater is vital. Over time, minerals and sediments in your water can accumulate in the heat exchanger, reducing its heating efficiency and potentially leading to costly repairs. By flushing your water heater, you can significantly extend its lifespan and ensure peak performance.
Preparation: Gather Your Tools and Materials
Before you begin, ensure you have the following tools and materials on hand:
- 2 buckets (5 gallons each)
- A garden hose
- Rubber gloves
- A screwdriver
- Tap water (preferably dechlorinated)
- A navigation manual for your specific Navien model (for reference)
Find the Drain Valve and Flush Kit
First, locate the drain valve and flush kit on your Navien water heater. The drain valve is usually at the bottom of the unit, while the flush kit, consisting of a T-handle and a gasket, is typically stored inside the front access panel.
Refer to your Navien navigation manual for the exact location of these components in your specific model.
Turn Off the Water Supply and Power
Before you begin the flushing process, it's crucial to turn off both the water supply and power to your water heater to ensure safety:
- Shut off the water supply valve located on the cold water inlet pipe.
- Turn off the electrical power at the circuit breaker panel.
Wait for a few minutes to allow any remaining hot water to cool down.
Connect Your Hose and Start Draining
Now that you've prepared your Navien water heater for flushing, it's time to start draining the system:
Attach the Garden Hose
Attach one end of your garden hose to the drain valve. Make sure the other end of the hose is directed towards a suitable drain, such as a floor drain or outdoors away from plants and water sources.
Open the Drain Valve and T-handle
Slowly turn the drain valve counterclockwise to open it. At the same time, open the T-handle on the flush kit. This will start draining the water from your Navien water heater into the bucket through the garden hose.
Allow the water to drain completely. This may take several minutes, so be patient.
Rinse the System with Tap Water
Now that the water has been drained, it's time to rinse the system with tap water to remove any remaining sediment:
Close the Drain Valve and T-handle
Once the water has finished draining, close the drain valve and T-handle by turning them clockwise.
Fill the System with Tap Water
Slowly fill the system with tap water (preferably dechlorinated) by opening the cold water supply valve you previously turned off. Allow the water to fill the system slowly to avoid causing an airlock.
Monitor the process closely to ensure no air bubbles are present in the system. If you notice any air bubbles, open the nearest hot water faucet until the water runs clear again.
Repeat the Draining and Rinsing Process
Repeat the draining and rinsing process at least 2-3 times to ensure all sediment has been removed from the system. After each rinse, inspect the drained water for signs of sediment. Once the water runs clear, your Navien water heater has been successfully flushed.
Reassemble and Restore Power
With the flushing process complete, it's time to reassemble your Navien water heater and restore its power:
Reinstall the Flush Kit
Return the flush kit to its storage location inside the front access panel and secure it in place.
Turn On the Water Supply and Power
Reopen the water supply valve and turn on the electrical power at the circuit breaker panel. Allow the water heater to begin heating up again.
Monitor the system closely for any leaks or other issues during this process.
Congratulations! You have successfully flushed your Navien tankless water heater. Regular flushing is key to maintaining your water heater's efficiency and longevity. We recommend flushing your Navien water heater at least once a year to keep it running smoothly. If you encounter any issues during the flushing process or notice inconsistent heating performance, don't hesitate to contact a professional plumber for assistance.
Now that your water heater is in top shape, you can enjoy an endless supply of hot water for all your cleaning, cooking, and comfort needs. Regular maintenance not only extends the life of your Navien water heater but also helps you save money on energy bills in the long run. So, stay proactive and keep your water heater in prime condition with regular flushing and care.