Easy DIY: Fix Pull Cable on Recliner in Minutes
Nothing is more relaxing than sinking into your recliner after a long day. But what happens when your footrest refuses to cooperate due to a broken pull cable?
Don't stress, fixing a pull cable on a recliner is a manageable DIY task. You don't need to be a professional upholsterer or shell out for expensive repair services. With the right tools, some problem-solving skills, and this comprehensive guide, you'll have your recliner good as new in no time.
Diagnosing the Problem
Before you start dismantling your recliner, it's crucial to understand what's gone wrong. Typically, a broken pull cable manifests in one of two ways:
Footrest won't raise: If you pull the control handle, but the footrest remains stubbornly flat, it's most likely that the cable has frayed, snapped, or come loose from its housing.
Inspect the Cable and Housing
First, carefully inspect the cable. Pull it gently to see if it's still securely attached. If it's broken, you might be able to see this with a visual inspection, or it may have frayed and unraveled. If the cable seems fine, the housing might be the culprit.
Check for any signs of damage or misalignment in the cable housing. Sometimes, these components can shift out of position, causing the cable to gothreaded and break.
Trace the Cable's Path
Next, follow the cable's path along the recliner's mechanism. Look for any tension points, sharp turns, or kinks that could be causing wear or tear on the cable. Taking note of these can help you when it's time to replace the cable.
Also, check if the cable is lubricated. Over time, lack of lubrication can cause friction and damage, leading to a snapped cable.
Gathering Your Tools and Replacement Parts
With a clear diagnosis, it's time to gather your tools and replacement parts. The exact parts you'll need may vary depending on your recliner's make and model, but here's a general list to get you started:
Tools: Screwdriver (Phillips or flathead, depending on your recliner's hardware), pliers, scissors, measuring tape, marker, and a needle-nose pliers.
Finding Replacement Parts
You can usually find replacement cables and housings at your local hardware store or online retailers. For better match, consider contacting your recliner's manufacturer. They often offer replacement parts designed specifically for their products.
Before purchasing, measure the length of the existing cable (if you're replacing it) and check the housing's size. A good rule of thumb is to buy a cable that's a couple of inches longer than you need, as you can always trim it down.
Safety First
Before starting any work on your recliner, make sure to unplug it from any power sources. Safety glasses and work gloves are also recommended to protect your eyes and hands from sharp edges or moving parts.
It's also wise to work in a well-lit area with plenty of space. You may want to move your recliner to a workshop or garage, or even outside if the weather permits.
Replacing the Pull Cable
Now that you've diagnosed the problem, gathered your tools, and sourced the necessary replacement parts, it's time to get started. Here's a step-by-step guide to replacing your recliner's pull cable:
Step 1: Disassemble the Recliner
Start by tilting the backrest up and removing the back cushion. Set these aside. Now, locate the screws that hold the recliner's back panel in place and remove them. Lift off the panel to expose the inner mechanism.
Be careful during this process. Some recliners may have sensitive electronic components. It's a good idea to take a picture of the mechanism before you start disassembling to help you remember how everything goes back together.
Step 2: Remove the Old Cable
Using your pliers and needle-nose pliers, gently pull out the old cable and remove it from the housing. If the cable is broken, you may need to use scissors to cut it and remove the pieces.
Ensure you don't damage the housing or the space where the cable runs. If the housing is damaged, you may need to replace it as well.
Step 3: Install the New Cable
Starting from the mechanism end, thread the new cable through the housing and along the cable's path. Ensure you're leading it in the same direction as the old cable.
Once you've reached the handle, secure the cable in place. You may need to use a washer or a bracket to keep it secure. Make sure to leave some slack, as you'll need to adjust the cable's tension.
Step 4: Tension the Cable
The cable should be tight enough that it can raise the footrest when you pull the handle, but loose enough that you're not straining to pull it. Too much tension can cause the cable to break again.
Start by pulling the handle to raise the footrest. While holding the footrest up, wiggle the cable gently. If there's too much give, you'll need to pull more of the cable through and secure it.
Step 5: Test the Cable
Once you've secured the cable, give it a test run. Pull the handle a few times to make sure the footrest raises and lowers smoothly and easily. If it seems to be working correctly, move on to the final step.
Step 6: Reassemble the Recliner
With the new cable successfully installed, it's time to put your recliner back together. Replace the back panel, ensuring that all the components fit properly. Then, replace the back cushion and tilt the backrest down.
Double-check that all screws are secure and give the footrest another test run to ensure everything is working as it should.
Lubrication and Maintenance
Regular maintenance can go a long way in preventing cable issues in the future. Here's how you can keep your recliner in top shape:
Lubrication
Periodically lubricate your recliner's moving parts, including the cable and cable housing. Use a light oil, such as WD-40, to coat these components. This will help reduce friction and wear, extending the life of your cable and other parts.
Be sure not to use too much oil, as excess can attract dust and dirt, causing more damage than good.
Regular Inspections
Every few months, give your recliner a visual inspection. Check for any signs of wear or damage, including frayed or broken cables. Catching problems early can prevent them from becoming bigger, more expensive issues.
Also, ensure that the recliner's mechanism is clean and free from obstruction. This will help prevent unnecessary strain on the cable and other components.
And there you have it! Your recliner is as good as new, and you've saved yourself the time and money of calling in a professional. Now, all that's left to do is kick back, relax, and enjoy your newly fixed recliner. Happy relaxing!