how to fix drawers that fall out

"How to Fix Drawers That Fall Out"

By Sarah Jackson
AD

Are you tired of your drawers constantly falling out or sticking? You're not alone. This common problem isn't just annoying, but can also damage your furniture and cause accidents. Thankfully, you can solve this issue with some simple fixes. Let's explore how to fix drawers that fall out, step by step, using both DIY methods and professional solutions.

A drawer that falls out usually has one of two problems: the drawer itself is too loose, or the drawer supports (also known as runner blocks or side runners) are worn out or incorrectly installed. Let's dive into the solutions for each of these cases.

Tightening Loose Drawers

If the drawer is simply too loose, you can tighten it and improve its stability.

AD
How To Fix Old Dresser Drawers From Falling Out
How To Fix Old Dresser Drawers From Falling Out
FIXING DRAWERS THAT FALL DOWN - Ridgid Driver and Before & After
FIXING DRAWERS THAT FALL DOWN - Ridgid Driver and Before & After
How To Fix Falling Drawers: A Step-by-Step Guide
How To Fix Falling Drawers: A Step-by-Step Guide

Before you start, make sure your tools are ready. You'll need a screwdriver (flathead or Phillips, depending on the hardware), a ruler, a pencil, and some wood glue if your drawer is constructed from wood.

Tightening-Box Drawer Slides

If your drawer uses metal slides (also known as box slides), follow these steps:

DIY Hack Fix a Falling Drawer - Drawer Falling out & Tilting down? Quck Temporary Fix
DIY Hack Fix a Falling Drawer - Drawer Falling out & Tilting down? Quck Temporary Fix
Simple Quick Dresser Drawer Fix
Simple Quick Dresser Drawer Fix
  1. Open the drawer fully.
  2. Locate the screws at the back edge of the drawer. These screws usually lie along a vertical or horizontal line.
  3. Using a screwdriver, turn the screws clockwise to tighten them. Be careful not to overtighten, as this can make the drawer too tight to open or close.
  4. Test the drawer by opening and closing it. If the drawer still falls out, continue turning the screw in small increments until you've tightened it as much as possible without causing friction.

Tightening Wooden Drawer Slides

If your drawer uses wooden slides (also known as English dovetail slides), follow these steps:

  1. Extract the drawer from the cabinet completely.
  2. Inspect the groove where the drawer slide runs. If the sides of the groove are worn out or cracked, you'll need to fill them with wood glue.
  3. Pour a small amount of wood glue into the groove, then use a rag or your fingers to push the glue into the sides. Be careful not to let glue drip onto other surfaces.
  4. Let the glue dry for at least 24 hours. Once it's dry, you can re-insert the drawer and test it.

Replacing or Fixing Worn Drawer Supports

If your drawer falls out because the supports are broken or worn out, you'll need to replace or repair them.

AD

Drawer supports can be constructed from many materials, including wood, metal, and plastic. The specific steps for replacing or repairing them will vary depending on the material and design. However, the basic process involves removing the old supports, preparing the space, and installing new ones.

Replacing Metal Drawer Supports

To replace metal drawer supports, you'll need a hacksaw or jigsaw, a drill, and sometimes a grinder or file.

  1. Remove the drawer from the cabinet.
  2. Locate the screws that hold the metal support in place. Remove these screws.
  3. Using your hacksaw or jigsaw, carefully cut off the old metal support. Be cautious when cutting to avoid damaging the wood or other cabinet parts.
  4. Use a file or grinder to smooth any sharp edges or burrs on the metal.
  5. Measure and cut your new metal support to fit the space. If necessary, drill new holes for the screws.
  6. Attach the new support using the provided screws.

Replacing Wooden Drawer Supports

To replace wooden drawer supports, you'll need a saw, sandpaper, wood glue, and clamps.

AD
  1. Remove the drawer from the cabinet.
  2. Identify the weak or broken parts of the wooden support. There may be cracks or breaks in the wood, or the support may be entirely missing.
  3. Use a saw to cut away the broken parts of the support. Be careful not to cut too deeply and damage the surrounding wood.
  4. Measure and cut new pieces of wood to replace the broken parts. The new pieces should match the shape and size of the original support.
  5. Sand the new wooden pieces to smooth any rough edges.
  6. Apply wood glue to the new pieces and the areas where they will meet the existing support. Use clamps to hold the pieces in place while the glue dries. Allow the glue to dry for at least 24 hours.
  7. Once the glue is dry, remove the clamps and inspect the repaired support. If necessary, use sandpaper to smooth any rough spots.

In many cases, you can prevent your drawers from falling out by regularly cleaning and maintaining them. Inspect your drawers periodically, and tighten or repair them as needed. Also, make sure to close your drawers gently to prevent excessive wear on the runners and other parts. By taking good care of your furniture, you can extend its lifespan and enjoy it for years to come.

A well-functioning drawer can be the difference between a chaotic and an organized home. With these fixes, you can keep your drawers from falling out and maintain a clutter-free, safe, and functional living space. Don't let a bothersome drawer become a constant annoyance. Take action today, and you'll soon be enjoying smooth, trouble-free drawer operation.

AD