how to fix bubbled drywall

DIY Drywall Repair: Fix Bubbled Plaster Like a Pro

By Daniel Anderson
AD

If you're noticing bubbled drywall in your home, you're not alone. This issue is quite common, especially in humid or poorly ventilated rooms. Before you grab your ladder and a bucket of joint compound, let's first understand what causes bubbled drywall and how you can fix it effectively.

Bubbled drywall, also known as blistering, often occurs due to moisture. This could be from water leaks, high humidity levels, or even water-based paint reacting with the drywall's paper facing. The moisture causes the paper to separate from the gypsum core, creating bubbles. Other culprits can be improper surface preparation, applying paint or wallpaper too soon after installation, or applying too thick a layer of joint compound.

Diagnose the Problem

Before you begin fixing the bubbles, it's crucial to identify the root cause. Grab a flashlight and examine the bubbles closely. If they're filled with water, the issue is likely moisture. If they're dry but still protruding, it might be a structural issue or a painting mistake.

AD
How to Fix Bubbled Drywall Tape & Repair the Paint
How to Fix Bubbled Drywall Tape & Repair the Paint
How to Fix Bubbles in Drywall Tape - Krista Howard Blog
How to Fix Bubbles in Drywall Tape - Krista Howard Blog
Expert Guide: How To Repair Water Bubble In Drywall
Expert Guide: How To Repair Water Bubble In Drywall

Remember, if the bubbles are due to water damage, you must first fix the leak or moisture problem, or the repairs will be temporary at best. Identify the source, possibly using a moisture meter, and address it before attempting to repair the drywall.

Assess the Damage

Use a sharp tool to gently poke the bubbles. If they're soft and yield easily, moisture is likely the cause. If they're hard and don't give way, it's probably a structural or painting issue. In either case, it's best to cut out the affected area and replace it.

How To Fix Messed Up Drywall Work! Bubbles And Craters! DIY
How To Fix Messed Up Drywall Work! Bubbles And Craters! DIY
How To Fix Bubbles In Drywall Tape? - (Best Ways!)
How To Fix Bubbles In Drywall Tape? - (Best Ways!)

Mark out the affected areas on the wall with a pencil, adding an extra inch around the bubbles to ensure you remove all damaged material. This will give you a clean patch to work with.

Prepare the Area

Turn off any power to the room for safety. Then, remove any trim, electrical covers, or other obstacles around the affected area. Cut out the marked section of drywall using a drywall saw or utility knife, creating a square or rectangular hole.

AD

Once you've cut out the damaged section, use a putty knife to clean up any debris. Also, inspect the studs and framing around the affected area to ensure they're dry and not damaged.

Repair the Drywall

Now that you've cut out the damaged section, it's time to replace it. The process involves a few steps, so let's break them down.

First, measure the size of the hole and cut a new piece of drywall to fit. Make sure the joint will be on a stud for added support. If not, you'll need to install a support, like a bridge or a Sister.

AD

Install the New Drywall Piece

Position the new piece of drywall in the hole, ensuring it fits snugly. Use drywall screws to attach it to the framing at the edges and in the center. Don't use nails as they can rip through the paper backing.

Once the new piece is secure, use joint tape to cover the seams. Apply a thin layer of joint compound over the tape, using a flexible putty knife. Let it dry according to the manufacturer's instructions.

Finishing Touches

After the initial layer of compound has dried, lightly sand the area with fine-grit sandpaper to remove any bumps or ridges. Wipe away any dust with a damp cloth, then apply a second layer of compound. Allow this to dry completely.

AD

Lightly sand the area again, then apply a thin layer of joint compound over the entire repaired section. This will create a smooth, even surface for painting. Allow it to dry completely, then paint the repaired area to match the rest of the wall.

Regularly inspect your drywall, especially in rooms prone to moisture, to prevent future bubbling. Proper ventilation, prompt repair of water damage, and careful painting can help maintain your drywall's health and longevity.

Now that you know how to fix bubbled drywall, you're equipped to tackle this common home repair issue. So, grab your tools, and don't let those bubbles get you down. Happy DIYing!

AD