how to fix a faucet handle that turns too far

Fix Faucet Handle That Turns Too Far: Easy DIY Steps

By Anthony Brown
AD

A stiff, over-turning faucet handle is a common plumbing issue, but it's also one of the easiest to fix. If your faucet handle turns too far and now struggles to control water flow, don't worry, you don't need to call a plumber just yet. With some basic tools and a little patience, you can fix this problem yourself and restore your faucet to full functionality. Let's dive into the steps you need to follow, tailored for both compression and ball faucets.

Before you start, ensure you have the necessary tools: an Allen wrench (for ball faucets), a flathead screwdriver, an adjustable wrench, and possibly some pliers. Also, have a few rags or an old towel ready to catch any water that might leak. Now, let's tackle the issue based on your faucet type.

Identifying Your Faucet Type

Faucets can be either compression or ball-type. Compression faucets use ceramic discs that sit on top of each other and solve by turning the handle up and down. Ball faucets, on the other hand, have a rotating ball joint that allows you to swivel the handle in various directions to adjust water flow.

AD
How To Fix Spinning Faucet Handle
How To Fix Spinning Faucet Handle
How To Fix A Faucet Handle That Turns Too Far? [7 Easy Steps]
How To Fix A Faucet Handle That Turns Too Far? [7 Easy Steps]
How to Fix a Stripped Faucet Handle – Step-by-Step Guide
How to Fix a Stripped Faucet Handle – Step-by-Step Guide

To identify your faucet type, look at the base of your faucet's handle. If it has a single lever that moves up and down and side to side, it's a ball faucet. If it has two separate handles, with a screw on top or a cap, it's a compression faucet.

Fixing a Compression Faucet Handle

Compression faucets often develop this issue due to wear and tear on the O-ring or the disc washer. Replacing these parts should fix the problem, and it's surprisingly simple.

Fix a Dripping Faucet Yourself (Simple DIY)
Fix a Dripping Faucet Yourself (Simple DIY)
how to fix a hard - to - turn faucet
how to fix a hard - to - turn faucet

First, turn off the water supply to your faucet using the shut-off valves underneath your sink. Then, remove the handle by taking off the cap or unscrewing the top screw with a flathead screwdriver. Next, remove the setscrew or escutcheon with an Allen wrench or a flathead screwdriver. Now, lift off the handle to expose the internal parts.

Repairing a Ball Faucet Handle

In ball faucets, the issue usually lies with the cam washer or the ball joint itself. Replacing these parts will make your faucet handle turn smoothly again.

AD

Start by turning off the water supply and dismantling the faucet handle using an Allen wrench. Remove the cap or the top screw, then lift off the handle. Next, unscrew the handle's setscrew using an adjustable wrench or pliers, and remove the cam washer. Finally, take out the faucet's ball joint, exposing the internal parts.

Replacing the Faulty Parts

Now that you've accessed the internal parts, you can replace the faulty components. Replacement parts are inexpensive and available at most hardware stores. If you're unsure about what needs replacing, take the old part with you to ensure a perfect match.

Before reassembling, make sure to clean the replacement part and the area around the faucet seat. This will help ensure a tight fit and prevent leaks. Once everything is clean and dry, start putting the faucet back together in reverse order from how you took it apart.

AD

Reassembling a Compression Faucet

Install the new O-ring or disc washer, then replace the faucet handle and all the screws. Don't overtighten the screws; just hand-tighten them. Once done, turn the water supply back on and test your faucet.

If your faucet still drips or handles turn too far, you might need to replace the entire cartridge. This process is similar to the above, but you'll also need to unscrew the faucet from the mounting nut and remove it from the sink.

Reassembling a Ball Faucet

Install the new cam washer, then replace the faucet ball joint and setscrew. Make sure the ball joint is aligned with the faucet neck, and the cam washer is seated properly. Once everything is in place, replace the faucet handle and screws, but don't overtighten them. Finally, turn the water supply back on and give your faucet a test run.

AD

There you have it - a repetitive, overly-turning faucet handle is no match for your newfound skills. Next time, you'll confidently tackle any torque issue like a pro plumber. Happy DIY-ing!

AD