how to drain gas from troy bilt snowblower

How to Drain Gas from Troy-Bilt Snowblower

By Joseph Thompson
AD

If your Troy-Bilt snowblower is causing more trouble than good, you might be considering retiring it. Before you do, consider draining the old gas and giving it a fresh start for next season. Here's a step-by-step guide on how to drain gas from your Troy-Bilt snowblower.

Draining the gas from your snowblower can prevent several issues.gas can deteriorate over time, clogging the fuel system and causing your engine to run poorly or not at all. Plus, old gas can leave behind deposits, which can be difficult and expensive to clean. Draining the gas at the end of each season ensures that your snowblower will start up reliably when the first snowfall hits.

Preparation

Before you begin, make sure you have all the necessary tools and equipment. You'll need a gas can, a siphon pump or a turkey baster, a funnel, and some old rags or towels for clean-up.

AD
How To Drain Gas From Snowblower The Easy Way
How To Drain Gas From Snowblower The Easy Way
Step By Step Guide On How To Drain Gas From Snowblower
Step By Step Guide On How To Drain Gas From Snowblower
How to Drain Gas from Snowblower? - Step-By-Step Guide
How to Drain Gas from Snowblower? - Step-By-Step Guide

Also, work in a well-ventilated area, preferably outside, to avoid gas fumes. If you're working in your garage, make sure the door is open and consider using a fan to increase airflow.

Locating the Gas Cap

First, you need to locate the gas cap on your Troy-Bilt snowblower. It's typically positioned on top of the fuel tank. The fuel tank might have a locking mechanism, so you may need to refer to your owner's manual to find out how to release it.

Draining the Fuel System
Draining the Fuel System
How to Start a Snowblower That Has Been Sitting
How to Start a Snowblower That Has Been Sitting

Once you've located the gas cap, remove it by turning it counterclockwise. Be careful not to lose the seal or washer inside the cap. If you do, you'll need to replace it with a new one before refilling the tank.

Siphoning the Gas

Now that you have access to the fuel tank, it's time to start draining the gas. If you're using a siphon pump, follow the manufacturer's instructions to attach it to the end of the fuel hose. If you're using a turkey baster, simply insert it into the fuel tank.

AD

With the siphon pump or turkey baster in place, insert the other end into a gas can. Then, create suction by squeezing the bulb or pump. When you release, the gas should be sucked out of the fuel tank and into the can.

Draining the Carburetor

Draining the gas from the fuel tank is a good start, but it's not enough. Gas can remain in the carburetor, which can also cause problems. Here's how to drain the gas from the carburetor.

First, locate the carburetor on your Troy-Bilt snowblower. It's usually positioned above the engine block and is recognizable by its small bowl and fuel lines running to and from it.

AD

Draining the Bowl

You can drain the gas from the carburetor's bowl by tilting the snowblower onto its side. This is the simplest method and works well if there's not too much gas left in the bowl. To do this, tip the snowblower onto its left side, with the carburetor facing up.

Tilt the snowblower at an angle so that the gas in the carburetor's bowl can drain out. You can catch the gas in a container or let it drain onto the ground. Be prepared to clean up any spills, and make sure to dispose of the gas responsibly.

Using the Priming Bulb

If your Troy-Bilt snowblower has a priming bulb, you can use it to drain the gas from the carburetor. The priming bulb is usually located on the side of the carburetor and is made of rubber.

AD

To drain the gas, squeeze the priming bulb several times to expel the gas from the carburetor. Each squeeze should release more gas into a container or onto the ground. Keep squeezing until no more gas comes out.

After you've drained all the gas from your Troy-Bilt snowblower, thoroughly clean the area around the fuel cap and carburetor to remove any gas residue. It's a good idea to let the snowblower sit for a day or two before storing it to ensure that all the gas has drained.

Preparing your snowblower for storage by draining the gas may seem like a hassle, but it's a crucial step in maintaining your lawn equipment. By taking the time to drain the gas, you're investing in the long-term health of your Troy-Bilt snowblower, ensuring that it will be ready to go when the first snowfall hits next winter. Don't forget to store the drained gas responsibly, and happy snow blowing!

AD