how to disassemble kenmore dryer

Kenmore Dryer Disassembly Guide

By Melissa Anderson
AD

Got a Kenmore dryer on the fritz? Before you call in the big guns, consider giving it a go yourself. Disassembling a Kenmore dryer might seem daunting, but with the right tools and some patience, you can handle it like a pro. Let's dive in.

First, ensure your safety. Unplug the dryer, turn off the gas or power supply if applicable, and let it cool down before starting. Always wear safety glasses and gloves, and remember, if you're unsure about any step, stop and consult a professional.

Gather Your Tools

Before you start, make sure you've got all the necessary tools. Here's what you'll need:

AD
How to Open a Clothes Dryer for Repairs
How to Open a Clothes Dryer for Repairs
Whirlpool/Kenmore Dryer Disassembly (#11079832800)/Repair Help | Repair Clinic
Whirlpool/Kenmore Dryer Disassembly (#11079832800)/Repair Help | Repair Clinic
How to Take Apart a Kenmore Dryer
How to Take Apart a Kenmore Dryer

1. Screwdriver set (flathead and Phillips)
2. Socket wrench set
3. Nut driver
4. Pliers
5. Needle-nose pliers
6. Safety glasses
7. Work gloves
8. Appliance lubricant (optional)

Kenmore Dryer Models

Kenmore dryers come in various models. Familiarize yourself with the model number of your dryer. You can find it on theustin side, near the door, or in the user manual. This will help you identify the specific disassembly process.

How to Completely Disassemble Whirlpool or Kenmore Dryer
How to Completely Disassemble Whirlpool or Kenmore Dryer
Kenmore Dryer Not Starting - How To Fix Kenmore Dryer
Kenmore Dryer Not Starting - How To Fix Kenmore Dryer

For this guide, we'll focus on Kenmore gas and electric dryers. While the process may vary slightly between models, the basic principles remain the same.

Preparation and Initial Disassembly

Once you've ID'd your model, it's time to prepare for disassembly. Lay out a blanket or towel on the floor to protect your dryer from scratches. Next, locate and disconnect the power supply. Once that's done, move the dryer and tilt it away from the wall to access the back.

AD

Start by removing the back panel. On most Kenmore dryers, you'll find it held in place by screws. Use a socket wrench or screwdriver to remove them. The panel should then slide off. If it's stubborn, wiggle it gently.

Drum Removal

With the back panel off, you'll see the dryer's drum. This is where things can get tricky. Drum removal involves patience and careful maneuvering:

1. **Belt Removal:** First, remove the belt from the drum pulley. To do this, release the tension on the drive motor pulley using a nut driver or socket wrench. Slowly slide the belt off the drum pulley.

AD

2. **Front Panel Access:** Next, remove the front panel. It's usually secured with screws at the top. Once the screws are out, you can slide the panel off.

3. **Drum Removal:** With the front panel off, you'll need to lift the drum out. You'll need help with this; the drum is heavy and unwieldy. Lift it out slowly, keeping it level to avoid damaging any components.

Drum Bearing and Axle Replacement

If you're replacing the drum's bearings or axle, the rest of the process should be smooth. Here's how:

AD

1. **Bearing Removal:** To remove the bearings, you'll likely need to use a bearing puller. Apply liberal amounts of appliance lubricant to the bearings before pulling them out.

2. **Axle Removal:** Once the bearings are out, you can pull the axle out of the drum. If it's stuck, you might need to use a hammer and a piece of wood to gently tap it out.

Reassembly

Reassembly is simply the reverse of disassembly. Here are a few tips:

1. **Drum Alignment:** When putting the drum back in, make sure it's correctly aligned. Most Kenmore dryers have an 'I' or 'L' shaped hole in the front to help with this.

2. **Belt Installation:** When installing the belt, make sure it's properly tensioned. Check your dryer's manual for the exact tension needed.

3. **Tighten Securely:** When reattaching panels and screws, make sure everything is tightened securely. Loose panels can cause damage and void your warranty.

And there you have it! You've successfully disassembled and (hopefully) reassembled your Kenmore dryer. Don't forget to test the dryer after reassembly to ensure everything's working as it should. Happy fixing!

AD