how to disassemble a kenmore dryer

Kenmore Dryer Disassembly Guide: Step-by-Step Instructions

By William Jackson
AD

Got a faulty Kenmore dryer on your hands? Before you shell out cash for a replacement, consider giving it a thorough check-up. Disassembling your Kenmore dryer for maintenance or repair can save you time and money. Here's a step-by-step guide to help you through the process, ensuring your safety and Kenmore dryer's longevity.

Before you start, remember to unplug the dryer from the power source and allow it to cool down. Safety first! Also, gather your tools - you'll need a screwdriver, pliers, and perhaps a hammer and chisel if removing nails. Let's dive into the disassembly process.

Preparation and Accessing Internal Components

Kenmore dryers have a similar design to most electric dryers, with the key components located behind the control panel. Understanding the layout will help you navigate the disassembly process.

AD
How to Open a Clothes Dryer for Repairs
How to Open a Clothes Dryer for Repairs
How to Take Apart a Kenmore Dryer
How to Take Apart a Kenmore Dryer
Whirlpool/Kenmore Dryer Disassembly (#11079832800)/Repair Help | Repair Clinic
Whirlpool/Kenmore Dryer Disassembly (#11079832800)/Repair Help | Repair Clinic

Start by removing the back panel. On most Kenmore models, you'll find the screws at the top and bottom edges. Unscrew and remove the panel gently, revealing the internal components.

Removing the Control Panel

The control panel is attached to the dryer's cabinet using screws. Typically, these are located at the top and bottom edges. Unscrew and remove the panel, along with any connecting wires. Be cautious while disconnecting; these wires handle the dryer's electrical components, so avoid any stress or tugging.

How to Completely Disassemble Whirlpool or Kenmore Dryer
How to Completely Disassemble Whirlpool or Kenmore Dryer
How to Replace the Belt on a Kenmore 70 Series Dryer
How to Replace the Belt on a Kenmore 70 Series Dryer

Once removed, you might need to disconnect the control panel's harness. Again, be careful not to damage any wires while doing this. Set the control panel aside for now, you'll reinstall it later.

Disconnecting Wiring Harnesses

Behind the control panel, you'll find various wiring harnesses connected to the dryer's motor, heating element, and thermostat. Use a flathead screwdriver to gently pry open the connectors and disconnect these harnesses. Label the wires as you disconnect them to ensure correct reconnection later.

AD

Now that the wires are disconnected, you can proceed to the next step. However, remember to keep your labelled wire diagram safe. It's your roadmap back to assembling your Kenmore dryer.

Accessing and Removing Major Components

With the control panel and wiring harnesses out of the way, you can now access and remove the major components of your Kenmore dryer. These include the blower wheel, heating element, and motor. Here's how to tackle each:

Removing the Blower Wheel

The blower wheel is located behind the dryer's drum. To remove it, you'll need to access it from the back of the dryer. You might need to remove an access panel or the exhaust duct to do this. Once you've accessed the blower wheel, use pliers to remove the retaining clips and pull the wheel out.

AD

Removing the Heating Element and Thermostat

The heating element and thermostat are typically located behind the dryer's control panel. They're connected to the dryer's cabinet using screws or nuts. Unscrew or unthread these fasteners and carefully remove the heating element and thermostat.

As you remove these components, be cautious not to damage the brittle porcelain insulation around the heating element. Also, keep track of any gaskets or seals you remove; you'll need to reinstall them when you reassemble your Kenmore dryer.

Disassembling the Drum and Lid

If you need to access or replace parts like the dryer's belt, you'll need to remove the drum and lid. Here's how:

AD

Removing the Drum

The dryer's drum is supported by a glide or roller at the front and a center shaft at the back. You'll need to remove both to complete the disassembly. Start by removing the front glide or roller. This is usually secured with a setscrew that you can access from the front of the dryer. Remove this setscrew and pull out the glide or roller.

Next, remove the center shaft. This is usually held in place by a nut that you can access from the back of the dryer. Unscrew this nut and pull the center shaft out. With both supports removed, the drum should slide out of the dryer's cabinet.

Removing the Lid

Once the drum is out, you can remove the lid. The lid is connected to the drum using a hinge mechanism. This mechanism is usually secured with screws or nuts. Unscrew or unthread these fasteners and carefully remove the lid. Be sure to keep track of any hardware you remove.

With these steps, you've successfully disassembled your Kenmore dryer. Whether you're repairing or replacing parts, make sure to follow a similar reverse process when reassembling. And remember, safety first - always ensure your Kenmore dryer is unplugged and cooled down before beginning any work.

Now that you've seen how straightforward a Kenmore dryer disassembly can be, why not tackle that maintenance or repair task you've been putting off? It's not as daunting as you might think. Happy fixing!

AD