how to cut common rafters

Mastering Rafters: Step-by-Step Guide on How to Cut Common Rafters

By Mark Brown
AD

Embarking on a construction or home improvement project often involves the need for common rafters. These key structural components support your entire roof and require careful cutting to ensure a solid, stable result. But what's the best approach to cutting common rafters? Let's explore the process, step by step.

First, ensure you have the correct tools for the job – a circular saw, tape measure, calculator for angles, and a carpenter's square. Safety gear, including gloves, goggles, and ear protection, is also essential. Now let's delve into the process, starting with determining the rafter's run.

Calculating Rafter Length and Cut Angles

Before you cut, you must calculate the appropriate rafter length and the required angle for the birdsmouth cut – the cut that fits the rafter against the top plate. The run (horizontal measurement) of the rafter is usually the wall length plus twice the rise over run (the vertical rise divided by four).

AD
a man working on some wood with the words rafter basics layout and cut common rafters
a man working on some wood with the words rafter basics layout and cut common rafters
How to Cut a Rafter Birdsmouth
How to Cut a Rafter Birdsmouth
Как правильно делать вырезы в стропилах каркасного дома? - Проектное бюро «КаркасГид»
Как правильно делать вырезы в стропилах каркасного дома? - Проектное бюро «КаркасГид»

To calculate the angle, use this formula: tangent(angle) = rise / run. Plug in your measurements, and you'll get the angle. For example, with a rise of 10 inches and a run of 120 inches, the angle is approximately 4.82 degrees.

Setting Up the Circular Saw

Once you've determined the cut angle, set your circular saw to match. If your saw doesn't have a built-in bevel gauge, use a combination square or miter box to set the correct angle. Always double-check your settings before cutting.

How To Make Common Rafters [Measure, Mark & Cut]
How To Make Common Rafters [Measure, Mark & Cut]
a man standing in front of some wooden planks
a man standing in front of some wooden planks

Secure the rafter firmly in place, with the area to be cut overhanging your saw's base plate. Ensure the rafter is stable and positioned correctly; safety should always be your paramount concern.

Making the Birdsmouth Cut

A birdsmouth cut requires a precise, angled cut at the base of the rafter. Mark the angle on your rafter using your calculated angle. Set your circular saw to match this angle and make the cut slowly and steadily. Always cut along the waste side of your line to ensure accuracy.

AD

After cutting, check the fit against your top plate. If necessary, fine-tune your cut with a handsaw or chisel. Remember, it's easier to remove a bit more material than it is to add it back if you cut too deep or wide.

Cutting the Rafter Tail

With the birdsmouth cut complete, now it's time to cut the rafter tail – the end that goes against the ridge board. This cut is typically a square cut unless you're creating hips or valleys, in which case you'll need to follow specific cutting instructions for those designs.

Measure and mark the length of the rafter tail, usually the same as the width of your roof. Ensure your rafter overhangs your wall evenly on both sides. Use your circular saw to make a square cut at this mark. Again, always check yourMeasure twice, cut once to ensure accuracy.

AD

Creating Rafters with Joggles

In some cases, you may need to create rafters with joggles – small notches cut out to accommodate plumbing or other obstructions. Measure and mark the joggle location. Using your circular saw, make cuts to create the joggle. Be extremely careful when making these cuts, as they can be challenging and risky.

Always ensure the joggle fits correctly around the obstruction. If not, fine-tune your cut as needed. Double-check your work to ensure the rafter is structurally sound before installing it.

Cutting Rafters with Hips or Valleys

For roofs with hips or valleys, you'll need to create compound cuts – cuts at two different angles. Calculate the angles as you would for a birdsmouth cut, then set your circular saw accordingly. Make your cuts slowly and carefully, ensuring they're accurate.

AD

After cutting, dryfit your rafters on the ground to ensure they all fit together correctly. If necessary, make any adjustments before installing them on your roof.

Now that you've mastered the art of cutting common rafters, you're ready to take your woodworking skills to new heights. Always prioritize safety and accuracy, and never hesitate to double-check your measurements. Happy building!

AD