how to curve trex decking

Mastering Trex Decking: Expert's Guide on How to Curve

By Steven Rodriguez
AD

Embarking on a project to revamp your outdoor space with Trex composite decking? You're in the right place. Trex, renowned for its durability and low-maintenance features, can transform your backyard into a stylish, functional haven. But wait, you've got a curve in mind? No worries! This guide will walk you through how to curve Trex decking, ensuring your outdoor space is not just functional but also visually stunning.

Before we dive in, it's crucial to understand that curving Trex decking is a unique process that cannot be achieved with basic tools. Trex offers a service called Trexvie, which allows for custom, curved deck boards. However, if you're seeking a DIY approach, here's a step-by-step guide for curving Trex decking using a router and flexible cutting guide. Let's dive right in!

Planning Your Curve

Planning is key before you start cutting. Measure your curve's radius, and sketch it onto the deck board, marking your cut lines. Remember, Trex composite boards can only be curved along their widths, not their lengths.

AD
How to Install Curved Decking
How to Install Curved Decking
How to Install Curved Decking
How to Install Curved Decking
Build Curved Decking in 2 minutes - Branches of Hogan
Build Curved Decking in 2 minutes - Branches of Hogan

You'll need a flexible cutting guide to achieve the curve. You can buy one, or make your own by securing a flexible material, like Masonite, to a straight edge with screws. Your guide should match the radius of your curve.

Gathering Your Tools

To curve your Trex decking, you'll need a plunge router, a flexible cutting guide, clamps, a fence, a speed square, a pencil, safety gear, and, of course, your Trex composite boards.

17+ Inspiring Curved Deck Ideas for Your Home
17+ Inspiring Curved Deck Ideas for Your Home
TREX CustomCurve - Deck Parts Bending - Glenbrook U
TREX CustomCurve - Deck Parts Bending - Glenbrook U

Safety first! Ensure your workspace is clean and well-lit. Wear protective gear, including safety glasses, work gloves, and a dust mask. Additionally, secure your board to a stable work surface using clamps or a fence to prevent slippage during cutting.

Setting Up Your Router

For this process, you'll use a plunge router set to follow the flexible cutting guide. Attach the guide to your router. Then, set your router's plunge depth to match the thickness of your Trex board, typically 1 inch.

AD

Next, configure your router's bit.Trex recommends using a flush-trim bit, as it will provide the cleanest cut. Ensure your bit is in good condition and properly seated in the router's collet.

Routing the Curve

Once your router and guide are set up, you're ready to route the curve. Starting at one end of your board, align your flexible guide with your cut line. Gently apply pressure to the router, allowing it to follow the guide's curve. Work slowly and steadily, ensuring the router bit cuts all the way through the board.

If you're cutting a long curve, expect to make multiple passes. After the first pass, flip the board over and repeat the process. This will ensure a smooth, even curve on both sides of the board.

AD

Safety Considerations During Routing

Always keep your hands behind the bit during operation. The router-bit creates a significant amount of force, so it's crucial to keep your hands out of harm's way.

Additionally, keep an eye on the router during operation. If it starts to smoke or the motor overheats, turn it off immediately to prevent damage.

After routing, allow the freshly cut board to cool before handling. This will prevent warping and ensure the cut is as accurate as possible.

AD

Sanding and Finishing

Trex composite boards may have rough edges after routing, so sanding is necessary. Start with coarse sandpaper (60-80 grit) to remove large imperfections, then finish with a fine-grit paper (120-150 grit) for a smooth surface.

Wipe the board clean with a damp cloth, then apply a finish to protect it from the elements. Trex offers a range of stains and sealers to complement your deck's design.

Your curved Trex decking is now ready for installation. Remember, proper spacing between boards is crucial for drainage and to prevent warping. Usual spacing is about 1/8 inch on universal joists and 3/16 inch on joists over 16 inches apart.

Install your curve with confidence, knowing you've added a unique, stylish touch to your outdoor space. Happy curving!

AD