how to clean jandy pool filter

How to Clean Your Jandy Pool Filter

By Christopher Brown
AD

Maintaining a clean and healthy pool requires regular upkeep, including the cleaning of your pool filter. If you're a Jandy pool owner, you're in luck! This guide will walk you through the process of how to clean your Jandy pool filter, making it a simple and straightforward task.

Properly cleaning your Jandy pool filter not only extends the life of the filter but also ensures your pool water remains crystal clear. So, let's dive right in and make your pool Maintenance a breeze!

Understanding Your Jandy Pool Filter

Before we delve into the cleaning process, it's crucial to understand the type of Jandy pool filter you have. Jandy filters primarily come in two types: D.E. (Diatomic Earth) filters and cartridge filters. Both types require regular cleaning, but the process differs slightly. In the next sections, we'll guide you through cleaning both types.

AD
How to Clean a Pool Filter (Sand, Cartridge, D.E.)
How to Clean a Pool Filter (Sand, Cartridge, D.E.)
Effortlessly Clean Your Pool Filter Cartridge
Effortlessly Clean Your Pool Filter Cartridge
How to Clean a Pool Cartridge Filter System
How to Clean a Pool Cartridge Filter System

It's also essential to locate your pool filter's MultiCyclone, a feature unique to Jandy filters. The MultiCyclone helps extend filter cycles by removing larger particles from the water, reducing the workload on your filter. We'll include a section on cleaning this component as well.

Cleaning a Jandy D.E. Filter

D.E. filters use a special powder called diatomaceous earth as the filter media. Follow these steps to clean your Jandy D.E. filter:

How Do I Backwash a Sand Filter in My Fiberglass Pool? - Thursday Pools
How Do I Backwash a Sand Filter in My Fiberglass Pool? - Thursday Pools
a poster with instructions on how to change the sand in a pool filter and how often it
a poster with instructions on how to change the sand in a pool filter and how often it
  1. Start by backwashing your filter. Most Jandy filters have a backwash setting on the control valve. This reverses the water flow, flushing out debris and dirt from the filter.

  2. After backwashing, open the drain at the bottom of the filter tank and drain the dirty D.E. powder.

  3. Next, you'll need to remove the grids from the filter tank. These grids hold the D.E. powder. To do this, close the multiport valve, turn off the filter pump, and relieve any pressure in the system by opening the air relief valve at the top of the tank.

  4. Now that the grids are exposed, rinse them thoroughly with a garden hose. This helps to remove any remaining D.E. powder or dirt.

  5. Once the grids are clean, reinsert them into the filter tank, making sure they're properly aligned and seated.

  6. Reassemble the tank, ensuring all gaskets are in place and not damaged.

  7. Finally, add new D.E. powder to your filter. A standard rule of thumb is to add one pound of D.E. per ten square feet of filter area. With your pool running, slowly add the D.E. to the skimmer, allowing the filter to circulate and evenly distribute the powder.

Cleaning a Jandy Cartridge Filter

Cartridge filters use large, pleated filter cartridges as the filter media. They're easy to clean and don't require adding D.E. powder like their D.E. counterparts.

  1. Begin by turning off the filter pump and relieving any pressure in the system by opening the air relief valve at the top of the filter canister.

  2. Remove the filter cartridge, usually by turning a knob or using a tool like a cartrige removal key. Slide the cartridge out and set it aside.

  3. Inspect the cartridge for any signs of wear and tear. If the cartridge is severely damaged or worn, it's time for a replacement.

  4. Rinse the filter cartridge thoroughly with a garden hose. For tougher cleaning, you can use a cartridge cleaning spray designed for your filter type.

  5. After rinsing, allow the cartridge to air dry completely before reinserting it into the filter canister.

  6. Once the cartridge is dry, reinsert it into the filter canister and reassemble the tank.

Cleaning the Jandy MultiCyclone

The Jandy MultiCyclone acts as a pre-filter, removing larger particles from the pool water. Regular cleaning of this component ensures its continued efficient operation.

AD
  1. Turn off the filter pump and open the bleed-off valve on the MultiCyclone, allowing water to drain from the system.

  2. Remove the dirt canister, located at the bottom of the MultiCyclone. Check the manufacturer's specifications for the correct procedure for your MultiCyclone model.

  3. Rinse the dirt canister with a garden hose, removing any debris or dirt from within.

  4. Reassemble the MultiCyclone, ensuring all parts are properly seated and functioning.

Regular cleaning of your Jandy pool filter and MultiCyclone will not only lengthen their lifespan but also maintain your pool's water quality. It's a simple, straightforward process that's well worth the effort. So, grab your supplies and get ready to dive into a clean, crystal-clear pool!

AD