how to clean carburetor briggs and stratton lawn mower

Simple Steps: How to Clean a Briggs & Stratton Lawn Mower Carburetor

By William Lopez
AD

The carburetor in your Briggs & Stratton lawn mower is a crucial component that regulates the amount of fuel entering the engine. Over time, it can become clogged with dirt, debris, and varnish, leading to poor engine performance or even failure to start. Regular cleaning of the carburetor is essential to maintain your lawn mower's efficiency and longevity. Here's a comprehensive guide on how to clean your carburetor and keep your Briggs & Stratton lawn mower running smoothly.

Before we dive into the cleaning process, ensure you have the following tools and materials readily available: a carburetor cleaner spray, a wire brush, a flathead screwdriver, rags or shop towels, safety glasses, and gloves. Also, have your Briggs & Stratton lawn mower's owner's manual handy for specific model information.

Understanding Your Carburetor

Familiarizing yourself with the basic components of your carburetor is key to understanding and troubleshooting any issues. The main parts you should know are the main jet, pilot jet, fuel inlet needle, and the float needle. These components work together to regulate the fuel-air mixture entering the engine.

AD
a lawn mower with the words how to clean lawn mower carburetor without removing it
a lawn mower with the words how to clean lawn mower carburetor without removing it
How to Fix a Lawn Mower by Cleaning the Carburetor [Briggs & Stratton and Tecumseh]
How to Fix a Lawn Mower by Cleaning the Carburetor [Briggs & Stratton and Tecumseh]
How to clean and maintain your Briggs and Stratton 675 Series Carburetor
How to clean and maintain your Briggs and Stratton 675 Series Carburetor

The carburetor's location can vary depending on your Briggs & Stratton lawn mower model, but it's usually connected to the engine block, with the intake manifold attached at the other end. Once you locate the carburetor, you'll notice the fuel bowl, where the fuel is stored before being drawn into the engine.

Pre-Cleaning Preparation

Before you start, ensure your lawn mower is cool to avoid any burns. Disconnect the spark plug wire to prevent the engine from accidentally starting. Place a container underneath the carburetor to collect any spilled fuel or cleaner.

How to Clean Riding Mower Carburetor (Fix Hard Starts Fast)
How to Clean Riding Mower Carburetor (Fix Hard Starts Fast)
How to Clean a Small Engine Carburetor
How to Clean a Small Engine Carburetor

Drain the fuel in thecarburetor by removing the Fuel Inlet Screw (also known as the low-speed screw) on the side of the carburetor using an Allen wrench. Unscrew it slowly until fuel starts to drip out. Once the dripping stops, reinsert the screw finger tight.

Cleaning the Carburetor

Spray the carburetor cleaner liberally onto a rag or directly onto the affected areas of the carburetor. Focus on the main jet, pilot jet, and the area around the fuel bowl. Allow the cleaner to soak for a few minutes to break down any built-up deposits.

AD

Using a wire brush, gently scrub the affected areas. Ensure you're thorough but careful not to damage the small jets and components. If necessary, use a flathead screwdriver to gently scrape off any stubborn deposits.

Removing and Disassembling the Carburetor

In some cases, you may need to remove the carburetor from the lawn mower for a more thorough cleaning. Consult your owner's manual for specific removal steps, but generally, you'll need to disconnect the fuel line, intake manifold, and the throttle cable.

Once removed, lay the carburetor on a work surface with the float needle pointing facing up. Unscrew the carburetor top with a wrench, being careful not to lose any small springs or parts. Clean each component thoroughly with the carburetor cleaner and a wire brush.

AD

Cleaning the Float Needle

The float needle plays a crucial role in regulating fuel flow into the carburetor. If it's stuck or dirty, it can cause flooding or starving the engine of fuel. To clean, first, remove the fuel bowl by unscrewing it from the bottom of the carburetor.

Remove the float and pin, then gently press the float needle out of its seat using a suitable screwdriver. Clean the needle and its seat with the carburetor cleaner and a wire brush. Reassemble in the reverse order, ensuring the float operates correctly and is well-seated.

Reassembly and Reinstallation

Once clean, reassemble the carburetor by reversing the disassembly process. Replace the fuel bowl and top, ensuring all components are properly seated and secured. Reinstall the carburetor onto the lawn mower, reconnecting the fuel line, intake manifold, and throttle cable.

AD

After reinstalling, start the engine to check for leaks and ensure it's running smoothly. If necessary, adjust the carburetor's idle mixture screw to fine-tune the engine's idle speed.

Regular carburetor cleaning is essential for maintaining your Briggs & Stratton lawn mower's performance. Make it a part of your annual maintenance routine to keep your engine running efficiently and extend its lifespan. If you notice persistent issues or severe damage, consider consulting a professional lawn mower repair service for further assistance.

AD