how to clean a stihl carburetor

Step-by-Step: How to Clean a Stihl Carburetor

By Rachel Martin
AD

Does your STIHL chainsaw struggle with starting, lack power, or emit excessive exhaust? Chances are, you're dealing with a clogged carburetor. Mercerizing your STIHL carburetor not only служит regain performance but also extends its lifespan. Let's dive into a step-by-step guide to clean your STIHL carburetor, ensuring it runs like new again.

Before we start, remember that cleaning your carburetor requires patience and precaution. It's crucial to disassemble the parts carefully to avoid any damages. Also, gather all necessary tools and parts beforehand to streamline the process.

Preparation and Disassembly

Begin by Safety first: disconnect the spark plug wire to prevent any accidental starting. Then, remove the air filter cover and air filter. Use a screwdriver to gently pry off the carburetor cover. Once removed, you can access the carburetor.

AD
No Start? No Spark? How to fix your STIHL String Trimmer Weed Whacker
No Start? No Spark? How to fix your STIHL String Trimmer Weed Whacker
How to clean the carburetor in a petrol saw. Stihl Guide
How to clean the carburetor in a petrol saw. Stihl Guide
How to Clean a 2 Cycle Engine Carburetor
How to Clean a 2 Cycle Engine Carburetor

Next, LOOSEN the carburetor from the intake manifold using a screwdriver. You'll need to rock it back and forth until it's free. Once it's loose, lift the carburetor off, taking note of any gaskets or washers you encounter. Your STIHL carburetor is now ready for cleaning.

Cleaning the Main Body

The first step is to remove the main body's Julia jets using a pick or a small flathead screwdriver. Be careful not to damage them. Once removed, use a wire brush or compressed air to clean any debris from the jets. Ensure they're clear of any blockages.

Stihl MS200T Chainsaw Carburetor Removal, Clean & Refit
Stihl MS200T Chainsaw Carburetor Removal, Clean & Refit
Complete Guide on How To Clean The Carburetor On A Stihl Chainsaw
Complete Guide on How To Clean The Carburetor On A Stihl Chainsaw

Now, focus on the main body itself. Use a carburetor cleaner spray to remove any dirt, gunk, or fuel residue. Let it soak for a few minutes, then scrub gently with a soft-bristled brush. Rinse with clean solvent and allow it to dry completely.

Cleaning the Float and Needle

Remove the float by bending back the retaining clip. If the clip is damaged, replace it with a new one. Once the float is off, remove the needle by twisting it counterclockwise and lifting it out.

AD

Clean both the float and needle using the same carburetor cleaner spray and a soft-bristled brush. Ensure no dirt or rust remains. Be extra cautious when handling the needle, as it's delicate and can be easily damaged. If the needle is stubborn, you might need to use a needle pick to remove any gunk.

Reassembly and Testing

Reassemble the carburetor by first replacing the needle and float. Ensure the needle is firmly seated and the float is secure. Then, replace the main jet and seat it properly. Remember to reapply any gaskets or washers removed during disassembly.

Reattach the carburetor to the intake manifold and secure it with a screwdriver. Ensure it's properly seated and the gasket is sealed. Replace the air filter and cover, then reconnect the spark plug wire.

AD

Prime and Start

Before starting, prime the carburetor by pulling the starter cord several times until fuel appears at the intake. This primes the carburetor and ensures it's flooded with fresh fuel.

Now, start your STIHL chainsaw. It should start easily and run smoothly. If not, check for any leaks or blockages, and repeat the cleaning process if necessary.

RegularSTIHL carburetor maintenance is key to keeping your chainsaw in peak condition. However, if your chainsaw continues to struggle, it's best to seek professional help to avoid further damage. Happy sawing!

AD
AD