how to clean a carburetor on a craftsman snowblower

Maximize Winter Efficiency: Step-by-Step Craftsman Snowblower Carburetor Cleaning

By Kevin Brown
AD

Keep your Craftsman snowblower running smoothly and efficiently with regular carburetor cleaning. A clean carburetor ensures accurate fuel-to-air mixing, preventing snowblower stall-outs, and improving overall performance. Here's a step-by-step guide to help you clean your Craftsman snowblower carburetor like a pro.

Before you begin, ensure you have all the necessary safety tools and gear. You'll need a flathead screwdriver, a pick set, a spray cleaner like WD-40 or carburetor cleaner, shop rags, gloves, and goggles for eye protection. Always disconnect the spark plug wire to prevent accidental starts while cleaning.

Preparation and Disassembly

The first step involves accessing the carburetor. Consult your Craftsman snowblower's manual to locate the carburetor, usually found behind the air filter. Remove the cover panel or any obstruction to expose the carburetor.

AD
HOW TO CLEAN A CARBURETOR ON A CRAFTSMAN 179CC SNOWBLOWER FOR BEGINNERS
HOW TO CLEAN A CARBURETOR ON A CRAFTSMAN 179CC SNOWBLOWER FOR BEGINNERS
How To Remove & Clean The Carburetor On An MTD/Craftsman 2-Stage Snowblower
How To Remove & Clean The Carburetor On An MTD/Craftsman 2-Stage Snowblower
DIY - Tecumseh Snowblower Carburetor Throttle Shaft Lever Repair PART 2
DIY - Tecumseh Snowblower Carburetor Throttle Shaft Lever Repair PART 2

Next, disconnect the fuel hose from the carburetor's inlet. Use a shop rag to catch any spilled fuel. If your snowblower has a fuel priming bulb or enrichment linkage, remove these components as well. With everything disconnected, gently remove the carburetor from the engine, taking note of its position and any washers or gaskets.

Removing the Carburetor

To remove the carburetor, look for mounting bolts that secure it to the engine. Usually, there are two bolts on the top and one or two bolts on the bottom. Use a socket wrench to loosen and remove these bolts, then carefully lift the carburetor off the intake manifold.

HOW TO CLEAN TECUMSEH SNOWBLOWER CARBURETOR
HOW TO CLEAN TECUMSEH SNOWBLOWER CARBURETOR
HOW TO ADJUST SNOWBLOWER CARBURETOR
HOW TO ADJUST SNOWBLOWER CARBURETOR

If your carburetor has a choke lever or linkage, gently disconnect it from the engine. Be sure to mark or photograph its position for proper reassembly. Once the carburetor is free, set it aside in a well-ventilated area for cleaning.

Inspecting the Carburetor

Begin by inspecting the exterior of the carburetor for any visible signs of damage or wear. Check for cracks, corrosion, or excessive carbon buildup around the fuel inlet and jets. If the carburetor is heavily damaged beyond basic cleaning, consider replacing it to restore optimal performance.

AD

Next, use a pick set to gently remove any debris or dirt from the idle mixture screw, main jet, and idle adjustment screw. Be careful not to damage the small passages and jets inside the carburetor. If the pick set isn't doing the trick, you can use a fine-bristled brush dipped in carburetor cleaner to clear out any stubborn deposits.

Cleaning the Carburetor

Before you start cleaning, make sure you're wearing appropriate safety gear, including gloves and goggles, to protect your hands and eyes from any harsh chemicals.(layout

Begin by spraying some carburetor cleaner into the fuel inlet area, taking care not to over-spray and damage precision components. Allow the cleaner to soak for about 15 minutes to break down any built-up dirt, carbon, or varnish. While waiting, you can use this time to clean other snowblower components, like the air filter.

AD

Cleaning with a Carburetor Cleaning Kit

If you have a carburetor cleaning kit, follow the manufacturer's instructions for optimal results. Typically, these kits come with a specialized spray or immersing solution that's designed to penetrate and dissolve buildup without damaging internal components. Soak the carburetor as directed, then give it a thorough rinsing with clean water.

After cleaning, allow the carburetor to dry completely. You can use compressed air to speed up the process, but be careful not to force too much air through the delicate jets. Wipe away any remaining cleaner with a damp cloth, then dry the exterior with a clean, lint-free shop rag.

Reassembling the Carburetor

Once your carburetor is clean and dry, it's time to reinstall it. Dry-fit the carburetor onto the intake manifold first, ensuring the gasket or washer is in place. Reinstall the mounting bolts by hand, then tighten them using a socket wrench. Be careful not to overtighten, as this can damage the gasket or warp the carburetor.

AD

Reconnect the fuel hose and any previously removed linkages or components. If you have a fuel primer bulb, squeeze it a few times to force fuel into the carburetor and clear any remaining cleaner residue. Finally, reattach the spark plug wire and give your snowblower a few pulls to work any remaining cleaner out of the system.

Post-Cleaning and Final Touches

After running your snowblower, inspect the carburetor and engine for any signs of leaks or residue. If everything looks good, consult your owner's manual for proper engine break-in procedures and fuel mixing instructions to ensure optimal performance after servicing.

Regularly maintaining and cleaning your Craftsman snowblower carburetor will help prevent performance issues and extend the life of your engine. By following this comprehensive guide, you'll be well on your way to a well-running, efficient snowblower season after season. Don't forget to store your snowblower properly during the off-season to protect its components and maintain peak performance.

AD