how to clean a briggs and stratton carburetor

Briggs & Stratton Carburetor Cleaning: Step-by-Step Guide

By Rachel Robinson
AD

As a Briggs & Stratton engine owner, you know that regular maintenance is key to keeping your engine running smoothly. One crucial aspect of this maintenance is cleaning the carburetor. But don't let that scare you; with the right steps, you can do it at home without any professional help. Let's dive into how to clean a Briggs & Stratton carburetor without any complexity.

First, it's essential to recognize the signs that your carburetor needs cleaning. If your engine is running roughly, stumbling, or hesitating, it's likely due to a clogged carburetor. Also, if your engine doesn't start easily or stays on for a short time before dying, these could be signs that your carburetor needs some tender loving care.

Gather Your Tools

Before you start, make sure you have all the necessary tools and supplies. This will make the process much smoother and ensure you don't damage your engine in the process.

AD
HOW TO CLEAN The Carburetor on BRIGGS & Stratton Quantum Lawnmower Engines
HOW TO CLEAN The Carburetor on BRIGGS & Stratton Quantum Lawnmower Engines
How to Clean a Plastic Briggs & Stratton Carburetor
How to Clean a Plastic Briggs & Stratton Carburetor
Easiest Way To Clean A Metal Briggs Carburetor
Easiest Way To Clean A Metal Briggs Carburetor

You'll need:

  • Pliers
  • Carburetor cleaner spray
  • Rags or paper towels
  • Screwdriver
  • Needle-nose pliers

Prevent Spills

Before you start, place a piece of cardboard under the carburetor to catch any drips. This will prevent any cleaning solution from damaging your engine or causing a mess.

How To Fix Briggs & Stratton Surging Engine | Nikki Carburetor Cleaning | Motor Hunts UP & DOWN
How To Fix Briggs & Stratton Surging Engine | Nikki Carburetor Cleaning | Motor Hunts UP & DOWN
How to Clean a Plastic Briggs & Stratton Carburetor
How to Clean a Plastic Briggs & Stratton Carburetor

Next, remove the air filter. This is usually as simple as lifting it off. But if it's held in place with screws, use a screwdriver to remove it carefully.

Disconnect the Carburetor

Now, you need to disconnect the carburetor from the engine. First, locate the carburetor to fuel line's fitting and gently remove it. Be careful not to spill any fuel.

AD

Next, using pliers, unscrew the mounting bolts that hold the carburetor in place. Once the bolts are loose, carefully pull the carburetor away from the engine. You may need to wiggle it a bit to disengage the gasket.

Clean the Carburetor Body

Now that you've removed the carburetor, it's time to clean the exterior. This step is crucial as it helps prevent debris from entering when you reassemble the engine.

Using a rag or paper towel soaked in carburetor cleaner, gently wipe the exterior of the carburetor body. Be careful not to let any cleaner get inside the carburetor as it can damage the inner components.

AD

Clean the Float

The float is a critical component of the carburetor. It helps regulate the flow of fuel into the engine. If it's not functioning properly, your engine won't run correctly. To clean it, remove the float bowl by turning it counter-clockwise and lifting it off. Always reassemble in the proper direction to prevent damaging the float.

Inside the float bowl, you'll find a float needle and seat. Use a toothpick or needle-nose pliers to gently remove any debris from the float needle and seat.

Clean the Jet

The jet is responsible for regulating the flow of fuel into the engine. If it's clogged, your engine might run poorly. To clean it, use a drill bit that fits snugly into the jet hole. Gently drill into the hole to dislodge any debris.

AD

If the jet is too small to fit a drill bit, you can use a wire or a small piece of straw to clean it. Gently push the wire or straw into the jet and twist it to dislodge any debris. Be careful not to push the debris further into the jet.

Reassemble the Carburetor

Once you've cleaned all the components, it's time to reassemble the carburetor. The process is essentially the reverse of removing it.

First, reattach the float bowl. Make sure to install it in the proper direction. Then, reconnect the fuel line and the mounting bolts.

Prime the Fuel System

Before you start the engine, you need to prime the fuel system. This helps ensure that fuel immediately reaches the engine once it starts.

To do this, remove the fuel line from the engine block and hold a finger tightly over the line opening. This creates a vacuum that draws fuel into the engine.

Once the engine is primed, reconnect the fuel line and wipe off any excess fuel.

Reinstall the Air Filter

Finally, reinstall the air filter. If you removed any screws, make sure to replace them securely.

Now, you're ready to start your engine. It should run more smoothly and efficiently now that your carburetor is clean.

Remember, regular cleaning is key to maintaining a healthy engine. As the saying goes, an ounce of prevention is worth a pound of cure. So, don't wait until your engine starts acting up before you clean your carburetor. Stay on top of your engine's maintenance for a smoother-running machine. Happy maintaining!

AD