how to check transmission fluid harley davidson

How to Check Transmission Fluid on Harley Davidson

By Matthew White
AD

Regular maintenance is crucial for keeping your Harley Davidson running smoothly and ensuring its longevity. One of the most important aspects of this is checking and maintaining your motorcycle's transmission fluid. Unlike cars, motorcycles don't have dipsticks for checking fluid levels, so a slightly different approach is needed. Let's dive into how to check transmission fluid on a Harley Davidson.

Before we start, let's ensure you have the necessary tools: a cotter pin remover or needle nose pliers, a 17mm socket wrench, and a transmission fluid catch pan. Now, let's get started.

Understanding Your Harley Davidson's Transmission System

The first step in checking your transmission fluid is understanding your motorcycle's transmission system. Harley Davidson's use either a 5-speed or a 6-speed cruiser transmission, depending on the model.

AD
How do you check transmission fluid on a Harley Davidson?
How do you check transmission fluid on a Harley Davidson?
Checking Oil on Harley and All Other Fluids
Checking Oil on Harley and All Other Fluids
How To Change Transmission Fluid - Harley Davidson Softail (Twin-Cam)
How To Change Transmission Fluid - Harley Davidson Softail (Twin-Cam)

Both these transmissions use a wet clutch system, which means the clutch plates are submerged in transmission fluid. This fluid not only lubricates the moving parts but also helps to displace heat away from the clutch. Checking and maintaining the right level of transmission fluid is key to keeping your motorcycle's transmission in optimal condition.

Locating the Filler Bolt

Once you've parked your motorcycle on a level surface and let the engine cool down, the first step is locating the filler bolt. On Harley Davidson's, this is found on the right side of the engine, near the top of the transmission case. It's a 17mm bolt with a cotter pin through the handle.

Harley 5 Speed Transmission Project: A Full Video Series
Harley 5 Speed Transmission Project: A Full Video Series
3 hole oil change Harley Davidson TOURING (2000 - 2017) Engine, Primary, Transmission Fluid service
3 hole oil change Harley Davidson TOURING (2000 - 2017) Engine, Primary, Transmission Fluid service

Before you proceed, ensure your motorcycle is on the center stand to avoid any oil spillage onto the tire. Also, make sure you're working in a well-ventilated area as the Harley Davidson's engine produces exhaust fumes even when the engine is off.

Removing the Filler Bolt

Using your 17mm socket wrench, carefully remove the cotter pin by bending it back and forth until it snaps. Then, remove the 17mm bolt using your wrench. Be cautious not to drop the bolt and pin into the transmission.

AD

Once the bolt is out, place the transmission fluid catch pan underneath the opening. The fluid may start draining immediately, so be ready to capture it. If the fluid dribbles out slowly, you may need to maneuver the bolt gently to break the seal.

Checking the Transmission Fluid Level

With the filler bolt out, you'll notice a small hole on the transmission case a few inches below the filler bolt. This is the dipstick for your Harley Davidson's transmission.

Insert a clean, dry, and straight object (like a clean, thin rod or a piece of wire) into the hole and push it all the way in until you feel it hit the bottom of the transmission case. Then, pull it out slowly. transmission fluid will cling to the object and give you an indication of the fluid level.

AD

Interpreting the Reading

The object you used should now have a film of fluid on it. Check the level of the fluid against the graduations etched onto the object. On Harley Davidson's, the ideal level is halfway between theFull and Add markings. If the fluid level is within this range, your transmission is in good condition.

However, if the level is low, you'll need to add more transmission fluid. Conversely, if the level is high, fluid may be leaking, and you should investigate the source of the leak. If the fluid is discolored (dark, burnt, or smells burnt), you'll need to change it and flush the system.

Adding Transmission Fluid

When adding transmission fluid, use only Harley Davidson's Genuine Parts Transmission Fluid or another brand approved by Harley Davidson, such as Motul or Royal Purple. These are specifically designed for Harley Davidson's wet clutch system.

AD

Using a funnel, slowly pour fluid into the transmission until it reaches the Full markings on your improvised dipstick. Take your time and regularly check the fluid level to avoid overfilling. Once you've reached the correct level, reinsert the filler bolt and cotter pin to secure it.

Regularly checking your Harley Davidson's transmission fluid is a key part of preventing major repairs down the road. By keeping an eye on your fluid levels and condition, you're ensuring your motorcycle stays in top condition. Happy riding!"

AD