how to check starter relay fuse

Check Starter Relay Fuse: A Step-by-Step Guide

By Brian Anderson
AD

Check engine light on your dashboard? One common culprit could be a faulty starter relay fuse. Here's a step-by-step guide on how to diagnose and check this critical component.

Understanding the starter relay and its fuse is crucial. They're part of your vehicle's electrical system, responsible for sending power to the starter motor when you turn your ignition key. If either is faulty, it could cause your engine to stall or, worse, not start at all.

Understanding Starter Relay Fuses

The starter relay fuse is designed to protect the electrical circuit from currents stronger than it can handle. When this fuse blows, it cuts off power flow, preventing potential damage to your vehicle's electrical system.

AD
an electrical wire is being hooked up to the wall by someone's hand and wires are plugged in
an electrical wire is being hooked up to the wall by someone's hand and wires are plugged in
How To Test a Relay (and How Relays Work) - in 8 minutes
How To Test a Relay (and How Relays Work) - in 8 minutes
Your Blinker's Broken? Check the Relay First
Your Blinker's Broken? Check the Relay First

So, how can you tell if your starter relay fuse is at fault? Let's dive into the process.

Tools Needed

Before starting, make sure you have the following tools:

How to test starter relay
How to test starter relay
What is a Start Relay? How Does It Work - The Engineering Knowledge
What is a Start Relay? How Does It Work - The Engineering Knowledge
  • A multimeter (preferably digital and with a range of 0-12 Volts)
  • Your vehicle's repair manual (for wiring diagrams and fuse box location)
  • Wire cutters
  • Safety glasses
  • Patience

Checking the Fuse

Once you've gathered your tools, follow these steps to check your starter relay fuse:

  1. Consult your repair manual to locate the fuse box and identify the starter relay fuse.
  2. Remove the faulty fuse, using the fuse puller tool if necessary, and inspect it. If the metal strip inside is broken or burnt, replace it.
  3. If the fuse appears intact, use your multimeter to test it. Set the multimeter to the lowest resistance setting (usually denoted by a symbol like Ω or Ω). If the fuse is good, it should read zero ohms. If it reads high resistance or does not register, replace it.

Testing the Starter Relay

Even if you've replaced the fuse, your engine may still not start if the starter relay is at fault. Let's test that too.

AD

Before starting, ensure your vehicle is in a safe, well-ventilated area, as testing the relay involves live electrical components.

Preparation

With your repair manual handy, locate the starter relay and identify where its wires connect to the engine wiring harness. Trace these wires to their respective connector.

Testing the Relay

Using jumpers or appropriate test leads, connect your multimeter to the relay's terminals. Most relays have four terminals, usually labeled 30 (power in), 87 (power out), 85 (ground), and 86 (coil).

AD
  1. Set your multimeter to the lowest resistance setting (Ω). Touch the red probe to terminal 30 and the black probe to terminal 85. The multimeter should read a low resistance (usually less than one ohm). If not, the relay is faulty.
  2. Next, touch the red probe to terminal 87 and the black probe to terminal 85. The multimeter should read infinite resistance or open circuit. If it reads low resistance, the relay is likely sticking and needs replacing.

If your relay tests faulty, replace it. Always double-check your repair manual for the correct replacement part number.

In many cases, checking and replacing the starter relay fuse or the relay itself will resolve your starting issues. However, if your engine still won't start, further diagnostics may be needed. Always err on the side of caution and consult a professional mechanic if you're unsure about any part of the process.

Now that you know how to check your starter relay fuse, you can keep your vehicle's electrical system in top shape and minimize potential breakdowns. Happy wrenching!

AD
AD