how to check power supply voltage

How to Check Power Supply Voltage

By James Thompson
AD

Checking the voltage of a power supply is a crucial task in electronics and DIY projects. It ensures the safety of your equipment and ensures optimal performance. Whether you're troubleshooting a circuit, selecting a suitable power supply, or determining if a battery needs replacing, understanding how to measure voltage is key.

Voltage is essentially the electrical 'pressure' that pushes charges around a circuit. Measuring it involves using a multimeter, a versatile tool designed for such purposes. Here's a comprehensive guide on how to check power supply voltage using a multimeter.

Preparing Your Multimeter

Before starting, ensure your multimeter is set to measure voltage. Most multimeters have a selector dial with symbols for different measurements. You'll want to choose the one denoted as 'V' or 'mV' for measuring voltage.

AD
an electronic circuit diagram with two different types of voltages and the same type of power supply
an electronic circuit diagram with two different types of voltages and the same type of power supply
How to Use a PSU Tester Correctly
How to Use a PSU Tester Correctly
an electronic device circuit diagram showing the current voltages and power source for this device
an electronic device circuit diagram showing the current voltages and power source for this device

Next, connect the multimeter probes. Theblack probe goes into the COM (Common) port, and the red probe into the V (Voltage) port. Double-check that your multimeter is set to 'DCV' for direct current voltage or 'ACV' for alternating current voltage, depending on the power supply you're measuring.

Safety Measures

Safety should always be your top priority when dealing with electrical systems. Before connecting your multimeter to a power supply, ensure that the power supply is switched off and disconnected from any source of electricity. Also, keep your hands dry and avoid touching electrical components unless you're wearing appropriate safety gear.

VFD Trouble? Fix It FAST — No Engineer Needed!
VFD Trouble? Fix It FAST — No Engineer Needed!
DIY Variable Linear Voltage Power Supply -Part 2
DIY Variable Linear Voltage Power Supply -Part 2

Once you've established a safe working environment, you can proceed to the next steps.

Measuring DC Voltage

For DC (Direct Current) power supplies, start by placing the multimeter probes on the '+' and '-' terminals, also known as positive and negative. Remember, positive to positive and negative to negative can cause damage to your multimeter. If the measured voltage is beyond your multimeter's range, switch the dial to a higher setting.

AD

Here's an example: If your multimeter measures up to 1000mV (milliVolts) and the power supply voltage is 12V, adjust the dial to the '20V' or '50V' setting for an accurate reading.

Measuring AC Voltage

For AC (Alternating Current) power supplies, you'll observe a similar process. Connect one probe to each terminal, ensuring you're not short-circuiting the system. Remember, AC voltage tends to fluctuate, so you might see slight discrepancies in your readings.

If you're unsure about the type of power supply (DC or AC), refer to its manual or look for labels on the device. They often specify the voltage type. Once measured, compare the reading to the expected voltage. If there's a significant difference, it might indicate a problem with your power supply.

AD

Interpreting Your Results

After measuring, you'll have a clear reading of your power supply's voltage. If it matches your expectations, your power supply is working as intended. If not, you might have a faulty power supply or an issue elsewhere in your circuit.

If the voltage is too high or too low, it could damage your equipment or make it inoperable. Always double-check your measurements and ensure the power supply's voltage matches what your circuit can handle.

Understanding Voltage Drop

Voltage drop is a phenomenon where the voltage decreases along a wire or through a component due to resistance. It's normal and can be calculated using Ohm's law (V = I * R). However, excessive voltage drop can lead to overheating and eventually, failure of components.

AD

While measuring voltage, keep an eye on the voltage drop across components to ensure they're functioning correctly and not dropping too much voltage.

Mastering the art of checking voltage is an indispensable skill in electronics. It's a precise and crucial process that ensures the longevity and safety of your equipment. So, whether you're a seasoned electronics hobbyist or just starting out, understanding how to measure voltage is key to your success.

Happy tinkering, and remember, safety first!

AD