how to change universal joint

How to Change a Universal Joint: Step-by-Step Guide

By Laura Brown
AD

The universal joint, or U-joint, is a critical component in your vehicle's drivetrain, responsible for transmitting power from the engine to the wheels. Located between the transmission and the drive shaft, it allows the transmission to operate at a different angle than the drive shaft, preventing excessive wear and tear. Over time and with regular use, these joints can wear out, causing vibrations and strange noises in your vehicle. When this happens, it's crucial to know how to change a universal joint to ensure your vehicle's safety and efficiency.

Before we dive into the step-by-step process, let's briefly discuss the tools and parts you'll need. You'll require a jack, jack stands, evolucion wrenches, a breaker bar, a U-joint press, and a U-joint removal tool. You'll also need a new U-joint kit, which includes the new joint, new cotter pins, and snap rings.

Preparing Your Vehicle

Before you begin, ensure your vehicle is safe and secure. Jack up the vehicle and support it securely with jack stands. Make sure the vehicle is level to prevent any part of it from shifting during the process. This step is crucial for your safety and the stability of your vehicle during the repair.

AD
How to change Universal Joints the EASY WAY!
How to change Universal Joints the EASY WAY!
a red and green toy car in a garage with an orange seat on the floor
a red and green toy car in a garage with an orange seat on the floor
an image of the parts for a steering wheel
an image of the parts for a steering wheel

Once your vehicle is secure, look under the vehicle to locate the U-joint. It's typically easy to spot, as it's a connecting point between the transmission and the driveshaft. Take note of any existing manufacturer marks on the joint and the surrounding area, as these will help you reassemble everything correctly.

Removing the Old Universal Joint

Before removing the old joint, you'll need to disconnect it from both the transmission and the driveshaft. Start by removing the cotter pin from the C-clip with the U-joint removal tool. This pin secures the C-clip in place, which holds the U-joint. Once you've removed the pin, the C-clip should slide off the retaining groove in the yoke.

How to Replace a Worn Out U-Joint | YourMechanic Advice
How to Replace a Worn Out U-Joint | YourMechanic Advice
Hot Rod How To & DIY Project Guides
Hot Rod How To & DIY Project Guides

Next, use a breaker bar and socket to loosen and remove the bolts holding the U-joint to the transmission and the driveshaft. Be sure to keep track of these bolts, as they are specific to your vehicle's make and model. Once the bolts are removed, carefully pry the U-joint off the yokes using a pry bar or a screwdriver. You may need to use some force, so be careful not to damage the surrounding parts.

Using a U-Joint Press

A U-joint press is a useful tool that simplifies the process of removing and installing U-joints. To use it, first, position the press on the U-joint in the yoke. Then, slowly apply pressure using the press's handle, forcing the U-joint out of the yoke. As the joint moves, ensure it doesn't shift too quickly, as this could cause it to fall and potentially damage other parts. Once the joint is out, discard it and prepare to install the new one.

AD

If you don't have a U-joint press, you can still remove the joint using the U-joint removal tool. This tool has a series of hooks that you can use to tediously pry the joint out of the yoke. It's a more time-consuming method, but it's effective with some patience and effort.

Installing the New Universal Joint

Now that the old U-joint is removed, it's time to install the new one. Begin by checking the new joint to ensure it's the correct type for your vehicle and that all components are present. Next, use the press to carefully install the new joint into the yoke. Unlike removing the joint, installing it requires only light pressure, as you don't want to force it in too tightly.

Once the joint is snug in the yoke, temporarily secure it with the new cotter pin. This will prevent the joint from shifting before you can fully secure it. Reinstall the yoke on both the transmission and the driveshaft, then loosely thread the bolts back into place. Make sure you match the bolts to their original positions, as they may have been switched during removal.

AD

Securing the New Universal Joint

With the yokes and the U-joint in place, it's time to secure everything. Tighten the bolts using a torque wrench, applying the manufacturer's specified torque value. Ensure you don't overtighten the bolts, as this could damage the joint or the surrounding parts. Once the bolts are secure, slide the new C-clip into place on the yoke. Use a small screwdriver or a punch to ensure it's fully seated in the retaining groove.

Finally, check for any signs of play or wobble in the new joint. If everything is secure and tight, you've successfully changed the universal joint. Replace the vehicle from the jack stands, lower it to the ground, and take it for a short test drive to ensure everything is working smoothly.

Regularly maintaining your vehicle's drivetrain can help prevent issues like worn-out universal joints. If you notice any unusual noises or vibrations coming from your vehicle, don't hesitate to investigate and address the problem promptly. Keeping your vehicle in good working order not only ensures your safety but also prolongs the lifespan of your vehicle. Happy wrenching!

AD
AD