how to change rzr belt without tool

How to Change RZR Belt Without Tools

By Olivia Thomas
AD

Changing a belt on your Polaris RZR can seem like a daunting task, but with the right technique and a little patience, you can do it without any special tools. In this guide, we'll walk you through the process step-by-step to help you confidently tackle this maintenance task.

Before we dive into the process, there are a few things you'll need to know. First, it's important to understand that the belt in question is the CVT (Continuously Variable Transmission) belt. It's responsible for transferring power from your RZR's engine to the wheels. Regular maintenance and timely replacement are crucial to ensure optimal performance and prevent unexpected breakdowns.

The Preparation Process

Before you start, ensure you have the following items ready:

AD
How to Replace a UTV or ATV Drive Belt
How to Replace a UTV or ATV Drive Belt
STV® Can Am Maverick X 3 Belt Changing Tool
STV® Can Am Maverick X 3 Belt Changing Tool
V-Belt Maintenance Guide | 5 Steps to Extend Belt Life & Prevent Failur
V-Belt Maintenance Guide | 5 Steps to Extend Belt Life & Prevent Failur
  • New CVT belt (make sure it's the correct type for your RZR model)
  • Gloves to protect your hands
  • Rags or shop towels to clean up any mess
  • Patience (changing this belt can take some time, especially if it's your first attempt)

Once you have everything ready, find a well-lit, flat surface to work on. It's also a good idea to have a wheel chock to keep your RZR in place while you're working.

Accessing the CVT Belt

Start by locating the engine cover on the left side of your RZR. Remove the four bolts securing it using a wrench or an impact driver. With the bolts removed, carefully lift the engine cover off and set it aside.

HOW TO CARRY A SPARE BELT & TOOLS - Dirt Wheels Magazine
HOW TO CARRY A SPARE BELT & TOOLS - Dirt Wheels Magazine
Primary Clutch Puller & Belt Change Removal Tool For Polaris Rzr Xp 1000 900 800
Primary Clutch Puller & Belt Change Removal Tool For Polaris Rzr Xp 1000 900 800

Next, you'll need to access the clutch cover. Remove the six bolts securing it using a wrench or an impact driver. Lift the clutch cover off, which will expose the CVT belt. You might need to use a pry bar to gently lift it off, as there's a gasket attached that can make it stick.

Removing the Old CVT Belt

Now that you can see the CVT belt, it's time to remove it. First, locate the clutch shoe pivot pin. It's a large pin that goes through the clutch shoe and holds everything in place. Using a punch or a small piece of firewood, carefully tap the pin out. You may need to use some force, but be careful not to damage the pin or the surrounding components.

AD

Once the pin is out, the clutch shoe should drop down, releasing the tension on the CVT belt. If it's not releasing, you might need to use a screwdriver or a pick to gently pry it open. With the tension released, you should be able topull the old CVT belt out. If it's stuck, you can use a pair of needle-nose pliers or a claw hammer to carefully pry it loose.

Installing the New CVT Belt

With the old belt out, it's time to install the new one. If you haven't already, consult your RZR's owner's manual to ensure you have the correct belt for your specific model. The new belt should look very similar to the old one, with a few notable differences. The new belt should have a shiny, untarnished appearance, and it should be more rigid than the old one.

To install the new belt, start by locating the marks on the input and output sheaves. These marks indicate the correct position of the belt on the sheaves. Align the new CVT belt with these marks and carefully slide it onto the input sheave. The belt should fit snugly, but not too tight.

AD

Aligning the New CVT Belt

Once the belt is on the input sheave, it's time to align it with the output sheave. Lift the clutch shoe back up and carefully slide the clutch shoe pivot pin back into place. You may need to use a hammer or a mallet to tap it into place. As you're doing this, make sure the belt is aligned with the marks on the output sheave.

If the belt isn't aligning properly, you might need to adjust the alignment tang on the output sheave. This is a small tab that sticks out from the sheave. Using a flathead screwdriver, gently bend the tab until the belt aligns with the marks.

Reassembling the Clutch Cover

With the new CVT belt installed and aligned, it's time to reassemble the clutch cover. Start by putting the clutch cover back onto the engine. Make sure the gasket is still in good condition and hasn't been damaged during the removal process. If it has, you might need to replace it.

AD

Secure the clutch cover with the six bolts you removed earlier. Make sure they're tightened evenly and to the correct torque, as specified in your RZR's owner's manual.

The Final Touches

With the clutch cover back on, it's time to put the engine cover back on as well. Secure it with the four bolts you removed earlier, making sure they're tightened to the correct torque.

Before you start your RZR, make sure to inspection the area around the CVT belt to ensure everything is functioning properly. Also, check that the belt isn't making any unusual noises when you start the engine. If it is, you might need to realign the belt or check for any other issues.

Congratulations, you've just successfully changed your Polaris RZR's CVT belt without using any special tools. Regular maintenance like this is crucial to keeping your RZR running in optimal condition. Always remember to consult your owner's manual for further reference and stay proactive about your RZR's maintenance. Happy riding!

AD