how to change oil on atv

Step-by-Step: How to Change Oil on Your ATV

By Steven Rodriguez
AD

Regular oil changes are crucial for maintaining your ATV's performance and longevity. Learn how to change oil on your ATV with this step-by-step guide to ensure optimal engine health and safety.

Before you start, gather the necessary tools and materials: an oil filter wrench, an oil drain pan, a funnel, gloves, safety glasses, new oil (check your owner's manual for the correct type and amount), and a new oil filter. Always remember to dispose of used oil and oil filters responsibly.

Preparation

First, allow your ATV's engine to run for about 10-15 minutes to warm up the oil. Warm oil flows more easily, making the drainage process smoother and preventing it from clumping up in the oil filter.

AD
Suzuki Quadrunner Oil Filter change! PowerModz!
Suzuki Quadrunner Oil Filter change! PowerModz!
How-To Adjust Your Valves - Dirt Wheels Magazine
How-To Adjust Your Valves - Dirt Wheels Magazine
Kids ATV Oil Change Complete Guide 2026 | Q9 PowerSports
Kids ATV Oil Change Complete Guide 2026 | Q9 PowerSports

Next, drive your ATV onto a stable, level surface, and use a jack to lift it safely. Support the ATV with jack stands for stability during the oil change process.

Draining the Old Oil

Locate the oil pan underneath your ATV, typically near the center of the vehicle. Position your drain pan beneath the oil pan, then use an oil filter wrench to loosen and remove the oil pan drain plug by hand once it's loose enough.

ATV Prep Made Easy: 10 Steps to Kickstart Your Spring Adventures!
ATV Prep Made Easy: 10 Steps to Kickstart Your Spring Adventures!
How to do an Oil Change on a Polaris Sportsman 500
How to do an Oil Change on a Polaris Sportsman 500

Allow the old oil to drain completely into the drain pan. Be patient, as this may take a few minutes. Once all the oil has drained, wipe the area clean with a cloth to remove any remaining oil. Replace and tighten the drain plug by hand, ensuring it's snug but not overtightened.

Replacing the Oil Filter

Position your drain pan beneath the oil filter. Using an oil filter wrench, turn the filter counterclockwise to loosen and remove it. Inspect the internal rubber gasket and replace it if necessary.

AD

Lightly coat the new oil filter's rubber gasket with clean engine oil, ensuring it covers the entire gasket. Screw on the new oil filter by hand, turning it counterclockwise until the gasket first makes contact, then turn it an additional 3/4 to 1 1/4 turns. Do not overtighten the oil filter, as this can cause it to leak or crack.

Adding New Oil

Locate your ATV's oil fill hole, usually on top of the engine, and remove the filling cap. Using a funnel, slowly pour the required amount of new oil into the engine, allowing it to settle between pours to ensure accurate measurement.

Once you've added the recommended amount of oil, replace the filling cap and allow the oil to settle for a few minutes. Check the oil level using the dipstick, wiping it clean before reinserting and removing it to get an accurate reading. Add more oil if necessary, in small increments, until the level is within the full range indicated on the dipstick.

AD

Checking for Leaks

Start your ATV's engine and allow it to run for a minute or two, ensuring the oil pressure light turns off. Turn off the engine and let the oil settle for another few minutes. Recheck the area around the drain plug and oil filter for any signs of leaks.

If no leaks are present, lower your ATV off the jack stands and let the engine run for a few more minutes to circulate the new oil. Check the oil level one last time and add more oil if necessary. Turn off the engine and properly dispose of the used oil and oil filter according to your local regulations.

Now that you've learned how to change oil on your ATV, make it a habit to perform this maintenance task every 3,000 to 5,000 miles or as recommended by your vehicle's manufacturer. Regular oil changes will help keep your ATV running smoothly and protect its engine for years to come. Happy trails!

AD
AD