how to change master cylinder clutch

How to Change Master Cylinder Clutch

By Richard Wilson
AD

Mechanically-minded motorcyclists often wonder how to change a master cylinder clutch. It's not as daunting as it sounds. Let's dive into this task with clear, step-by-step instructions. We'll ensure you have a solid understanding of the process, making it an easy task for you to undertake.

Changing a master cylinder clutch isn't just about replacing a worn-out part; it's also about maintaining your motorcycle's performance and safety. So, let's get started, shall we?

Gather Your Tools and Parts

Before you begin, assemble all the necessary tools and parts to avoid any mid-project trips to the store.

AD
Clutch Master Cylinder DIY Replacement 1.8T Golf MK4
Clutch Master Cylinder DIY Replacement 1.8T Golf MK4
the hydraulic clutch system is shown in an orange and black poster with instructions on how to use it
the hydraulic clutch system is shown in an orange and black poster with instructions on how to use it
Mastering the Basics of Hydraulic Clutch Systems
Mastering the Basics of Hydraulic Clutch Systems

Your checklist should include:

  • A new master cylinder clutch assembly
  • Allen wrenches (sometimes included with the new assembly)
  • Screwdriver (flathead and Phillips)
  • Pliers
  • Grease
  • Nitrile gloves
  • Shop towels or rags

Preparation: Find Your Master Cylinder

Park your motorcycle on a stable, level surface. Locate your master cylinder - usually a small metal cylinder connected to the clutch lever and nearby the motorcycle's handlebar.

How to Replace Clutch Master Cylinder 05-06 Hyundai Elantra
How to Replace Clutch Master Cylinder 05-06 Hyundai Elantra
a black and white photo with the words clutch master replacer on it's side
a black and white photo with the words clutch master replacer on it's side

Identify the bleed nipple at the top of the master cylinder, which you'll need to access for bleeding (releasing air) once you've installed the new assembly.

Disassembly: Removing the Old Master Cylinder

Start by removing the protective cover and any cables blocking your access to the master cylinder and clutch reservoir.

AD

Loosen the clutch cable at its adjustment point, then slide it off the pivot pin. Use pliers to gently bend theтейd end of the cable to help remove it from the input lever.

Using an Allen wrench, unscrew the clamp bolt attaching the clutch lever to the perch, then slide the lever off. Remove the old master cylinder.

Next, use a screwdriver to pry off the old reservoir. You might need to use a bit of force, so be careful not to damage the surrounding area.

AD

Install the New Master Cylinder Clutch

You're now ready to install the new master cylinder clutch assembly. This part might seem tricky, but with careful attention, you'll find it's not as daunting as it sounds.

Begin by applying grease to the pivot point where the lever attaches to the perch. This will help prevent excessive play and make your lever feel smoother.

Assembly: Installing the New Reservoir

Using the new reservoir's o-ring as a guide, position the reservoir on the master cylinder. Note the orientation - most reservoirs are marked with an 'up' arrow indicating the top.

AD

Engage the reservoir's locking tabs and gently push it until it's fully seated. Test the lock by trying to pull it back out - it should hold fast.

Concluding the Installation

Slide the new master cylinder into the handlebar, ensuring the reservoir's bolts align with the mounting holes. Push the reservoir back through the provided opening in the clutch perch.

Tighten the lower reservoir bolts by hand initially, then give them a few turns with a spanner wrench. Be careful not to overtighten.

Reinstall the clutch cable, engaging the cable with the input lever. Pull the cable tight as you slide the clutch lever on, then secure it in place with the clamp bolt.

Bleeding the New Master Cylinder

After replacing any cables or adjusters, it's essential to bleed the new master cylinder to ensure air doesn't get trapped in the system.

The exact process varies by motorcycle make and model, so consult your owner's manual for specific instructions. In general, you'll need to open and close the bleed valve while simultaneously applying and releasing pressure on the clutch lever.

After bleeding, check your clutch for correct operation and adjust it if necessary. Remember that adjustments should be made in small increments to prevent overadjusting.

Congratulations! You've just mastered how to change a master cylinder clutch. Regular maintenance like this ensures your motorcycle runs smoothly and safely. Happy riding!

AD