how to change libman tornado mop head

Easy Steps: Switching Your Libman Tornado Mop Head

By Amanda Rodriguez
AD

If your Libman Tornado Mop has seen better days, replacing its head might just breathe new life into it. But if you've never done it before, don't worry. This step-by-step guide will walk you through how to change a Libman Tornado mop head seamlessly and ensure a squeaky-clean outcome every time.

Before you begin, gather your new Libman Tornado mop refill head and a screwdriver (usually a Phillips #2 or #3). Also, ensure the replacement head is compatible with your mop model. Now, let's dive into the process.

Preparing to Install the New Head

Before installation, let's prep your Libman Tornado mop. This includes removing the old head and thoroughly cleaning the mop handle. This not only ensures a smooth fit for the new head but also prevents any germs or dirt from affecting your cleaning.

AD
How to Replace a Libman Tornado Mop Head in 60 Seconds
How to Replace a Libman Tornado Mop Head in 60 Seconds
The Libman Company Floor Cleaning Products Review
The Libman Company Floor Cleaning Products Review
How to Change a Rubbermaid Twist Action Mop Head
How to Change a Rubbermaid Twist Action Mop Head

To remove the old head, first, identify the mop's pivoting joint. This is where the head attaches to the pole. You'll see two screws securing it in place. Using your screwdriver, loosen and remove these screws. With the screws out, the old mop head should promptly detach.

Cleaning the Mop Handle

With the old head off, inspect the mop handle for any dirt or residue. Using a damp cloth, wipe the entire handle, including the pivoting joint and the areas around the screw holes. This ensures no debris hinders the attachment of the new head.

How to Reinstall the Mop Head on the Libman Freedom Spray Mop
How to Reinstall the Mop Head on the Libman Freedom Spray Mop
How to Clean a Mop Head - Easy Cleaning Hacks
How to Clean a Mop Head - Easy Cleaning Hacks

If you spot any sticky or tricky-to-remove marks, use a mild detergent or a bit of rubbing alcohol on a cotton bud to scrub it off gently. Remember, you're cleaning a mop, so be thorough, but also gentle to avoid damaging the handle.

Inspecting Your New Mop Head Refill

Before adhering the new head to your Libman Tornado mop, check the replacement head for any damage, such as frayed edges or loose strings. If everything looks good, measure the head to ensure it's the correct size and model for your mop.

AD

Correct fitting is crucial as an incorrect head could affect your mop's performance,άκbing your cleaning time, or even causing damage to your floor or mop. If you're unsure, double-check your existing mop head's specifications or consult Libman's official website.

Installing the New Mop Head

Now that your handle and the new head are primed, it's time to attach the new head. First, match the holes on the new head to the screw holes on the mop handle. Align the two pieces, ensuring the head's flat edge faces the floor.

Then, place the first screw in the hole and loosely secure it with your screwdriver. Do the same for the second screw, leaving both screws slightly loose for now. You'll tighten them later for a snug fit.

AD

Securing the New Mop Head in Place

With both screws loosely in place, you can now proceed to tighten them. Short, firm turns with your screwdriver should do the trick. Be careful not to overtighten, as this could strip the screw holes or damage the mop head.

Once securely fastened, grip the mop handle and give the head a gentle tug to ensure it's firmly attached. If there's no give, then your new Libman Tornado mop head is ready for action. If it wiggles, tighten the screws a little more.

Testing Your New Libman Tornado Mop Head

Now that you've changed your Libman Tornado mop head, it's time for a test run. Fill a bucket with water and add your preferred cleaning solution, or just plain water if you're using it for general floor cleaning. Soak the new mop head in the solution as you would with the old head.

AD

Squeeze the mop head to remove excess water, then begin mopping. The new head should glide across your floor effortlessly, picking up dirt and grime with minimal force. If it seems too heavy or unresponsive, check the screws to ensure they're not too loose or too tight.

And there you have it! You've successfully changed your Libman Tornado mop head. Now, keep your floor sparkling with regular cleaning and proper maintenance of your mop. Happy cleaning!

AD