Step-by-Step Guide: Change Washer in Delta Bathroom Faucet
Is your Delta bathroom faucet suddenly dripping or not functioning properly? It might be time to replace a worn-out washer. Changing a washer in a Delta bathroom faucet is a straightforward DIY task that can save you money and time. Whether you're a first-time homeowner or a seasoned DIY enthusiast, this comprehensive guide will walk you through the process step-by-step.
Before you begin, gather your tools and materials. You'll need a Phillips screwdriver, an adjustable wrench, a flathead screwdriver, a new washer that matches your faucet, and a cloth or towel to protect your sink andcatch any drips. Ensure you have the correct washer for your Delta faucet by checking the model number or taking a picture of the old washer to the hardware store.
Preparing Your Workspace
Prepare your workspace by turning off the water supply to your faucet. The valve is usually located under the sink. Once you've turned off the water, open the faucet to relieve any pressure in the lines and protect yourself from any sudden water release.
Protect your sink and faucet with a cloth or towel to prevent scratches or damage during the repair process. Now, let's proceed to disassemble the faucet handle and access the washer.
Removing the Faucet Handle
Using your Phillips screwdriver, remove the setscrew located on the underside of the faucet handle. This screw secures the handle to the stem and can usually be found at the top of the handle or on the side.
Once the setscrew is removed, gently lift the faucet handle off the stem. Some Delta faucets may require additional steps to remove the handle, such as unsnapping it or using a specific tool provided with the faucet. Consult your user manual if you're unsure about the removal process.
Exposing the Washer
With the faucet handle removed, you should now see the stem or cartridge assembly and the washer. The washer is a small disc located at the bottom of the stem or inside the faucet cartridge. It may be made of rubber orother durable material and sits against a small seat, which is the hole through which water flows into the spout.
To successfully replace the washer, you need to remove the stem or cartridge. The method of removal depends on the type of Delta faucet you have. Here, we'll provide instructions for both compression and cartridge faucets.
Replacing the Washer: Compression Faucets
Compression faucets use a small washer and seated valve to control water flow. They are typically found in older homes and require the removal of the entire stem for washer replacement.
Using an adjustable wrench, gently grip the packing nut that secures the stem within the faucet body. Turn the packing nut counterclockwise several turns as you support the faucet body with your other hand to prevent it from moving or breaking. Once you've released the packing nut, slowly lift the stem out of the faucet.
Removing the Old Washer
Locate the old washer at the bottom of the stem. It may be wedged tightly against the seat, so you might need to carefully pry it off using a small, flathead screwdriver. Discard the old washer and set it aside.
Before installing the new washer, inspect the seat for any damage or wear. If the seat is damaged, you may need to replace it or call a professional for assistance. Otherwise, clean the area gently to remove any debris or buildup.
Installing the New Washer
Position the new washer onto the tip of the stem. Ensure it fits correctly and is oriented properly against the seat. Gently lower the stem back into the faucet and align the packing nut.
Hand-tighten the packing nut clockwise, using just enough force to secure the stem and create a watertight seal. Be careful not to overtighten, as this can cause damage to the faucet components or create excessive pressure that could cause leaks or bursting.
Replacing the Washer: Cartridge Faucets
Cartridge faucets use a single, removable unit that controls water flow through a small cylinder. They are typically found in modern homes and require the removal of the cartridge for washer replacement.
Using your flathead screwdriver, gently pry off the cap or cover located at the top of the faucet handle. This will reveal the small setscrew that secures the cartridge in place. Remove the setscrew using your Phillips screwdriver.
Removing the Cartridge
Gently lift the cartridge out of the faucet using both hands and supporting the faucet body. Some cartridges may be held in place with an additional retaining clip that you'll need to remove first. If your cartridge uses one, carefully remove it using needle-nose pliers or a small screwdriver.
With the cartridge removed, locate the cam (the part that controls the water flow) and the washer. The washer is typically found in a small groove on the underside of the cam. Carefully pry the old washer off using a small, flathead screwdriver and discard it.
Installing the New Washer
Position the new washer onto the underside of the cam, ensuring it fits properly within the groove. Inspect the cam and seat for any wear or damage, and clean them gently if necessary.
Lower the cartridge back into the faucet, ensuring the handle aligns properly with the stem. Replace the setscrew and hand-tighten it, then secure the cap or cover back onto the faucet handle.
Once you've replaced the washer, turn the water supply back on by turning the valve under your sink clockwise. Run the faucet briefly to check for any leaks or issues, and make any necessary adjustments to the packing nut or setscrew. If your faucet is still leaking or not functioning properly, you may need to consult a professional or consider additional repairs.
By following these steps, you should now be able to successfully change the washer in your Delta bathroom faucet and restore it to proper working order. Regular maintenance and prompt repairs can help extend the lifespan of your bathroom fixtures and save you money in the long run. Happy DIYing!