how to change a pentair water filter

How to Change a Pentair Water Filter in 3 Easy Steps

By Emily Smith
AD

Tired of the taste or smell of your tap water? Ready to take control of your water quality? Changing your Pentair water filter can help ensure fresh, clean water for your home. Here's a step-by-step guide to help you through the process.

Before you begin, make sure you have the correct replacement filter on hand. Pentair offers a range of filters to accommodate different water needs. Check your current filter's model number to ensure a smooth replacement.

Preparation: Gather Tools and_frame

First, ensure you have all the necessary tools and materials. You'll need:

AD
a person is using a pressure gauge on a lawn mower
a person is using a pressure gauge on a lawn mower
How to Change the 4 Types of Water Filter
How to Change the 4 Types of Water Filter
How To Change Whole House Sediment Water Filter St
How To Change Whole House Sediment Water Filter St
  • Replacement filter
  • Screwdriver (usually Phillips-head)
  • Eyeglasses or magnifying lens (for reading small print)
  • Towel or bucket (to catch any water)

Once you've gathered everything, locate your water filter, typically found near your main water supply or under the kitchen sink.

Turn Off Water Supply

Before you start, it's crucial to turn off your main water supply to prevent messes and ensure safety.

a man pointing to the water filter that is in front of him and says, easy water filter replacer
a man pointing to the water filter that is in front of him and says, easy water filter replacer
Water Filter How to Clean the One You Have at Home
Water Filter How to Clean the One You Have at Home
  1. Find your main water supply valve, usually a lever or wheel near your water heater or where the main water line enters your home.
  2. Turn off the water by rotating the lever clockwise or closing the wheel.

Release Water Pressure

After turning off the water, release any remaining water pressure in the pipes to avoid leaks or damage during removal.

  1. Open a faucet connected to the water line you just turned off. This could be a kitchen or bathroom sink.
  2. Allow the water to run until the pressure has been released, and the flow slows to a trickle. This may take a few minutes.

Remove Old Filter

Once the water pressure is released, it's time to remove the old filter.

AD

Before you begin, note the position of the old filter to ensure you install the new one correctly. Most filters are removed by unscrewing or unlatching them.

Unscrew or Unlatch the Filter Housing

Depending on your model, you may need to unscrew a cap or unlatch a latch to access the filter.

  1. Use a screwdriver to turn the cap counterclockwise or release the latch.
  2. Remove the cap or lid and set it aside.

Remove the Old Filter

With the housing open, carefully remove the old filter from the housing.

AD
  1. Gently pull the old filter out of the housing. It may still have some water inside, so be prepared with a towel or bucket.
  2. Disposal of old filters varies by manufacturer, so check with your local waste management department for guidance. Some filters may be recyclable or reusable.

Install New Filter

Now it's time to install your new filter.

Before you begin, ensure you have the correct filter for your system. If you're unsure, check your owner's manual or contact Pentair's customer service.

Insert the New Filter

Installing the new filter is a simple reverse of the removal process.

AD
  1. Without touching the actual filter media (the white center area), insert the new filter into the housing. Ensure it's facing the correct direction, as indicated by an arrow or 'UP' marking on the filter.
  2. Gently push the filter into place until it's fully seated.

Reassemble and Tighten

Once the new filter is in place, reassemble the housing and tighten as needed.

  1. Align the lid or cap with the housing and place it back on.
  2. Turn the lid or cap clockwise to tighten it. Be careful not to overtighten as this can cause damage to the O-ring seal.

Final Steps: Test and Monitor

You've successfully changed your Pentair water filter! Now it's time to test your work and monitor performance.

Slowly Turn Water Supply Back On

Before turning the water back on, ensure all faucets are closed to prevent any water from leaking out and causing damage.

  1. Gradually turn the water supply valve back on. Start with a slow turn, then gradually increase the speed as you feel the water begin to flow.
  2. Listen for any leaks or unusual sounds. If you hear something, turn the water off immediately and check for any leaks.

Monitor Filter Performance

Regularly monitor your new filter to ensure it's working correctly and that your water quality remains high.

Pentair recommends replacing your filter every 6 to 12 months, depending on your water usage and quality. Regularly checking your filter can help you stay on top of maintenance and avoid unexpected filter changes.

Congratulations! You've successfully changed your Pentair water filter. Enjoy the fresh, clean water that comes with it. Regular maintenance like this helps ensure your whole-house water system stays in top shape, providing clean, safe drinking water for your family. Happy filtering!

AD