how to build xlr cable

"How to Build XLR Cable: A Step-by-Step Guide"

By Nicole Anderson
AD

Building your own XLR cable might seem daunting, but with the right tools and a bit of patience, you can create a high-quality, long-lasting cable tailored to your needs. This guide will walk you through the process, from gathering materials to the final product.

Before you start, make sure to understand that XLR cables are used for balanced audio connections, commonly in professional audio applications. They are known for their robust build and three-pin design. Let's dive into the step-by-step process of creating your own XLR cable.

Gathering Materials and Tools

To get started, you'll need the following materials and tools:

AD
How to Build Your Own XLR Cables: A Step by Step Guide - Studio DIY — The Home Studio Archive
How to Build Your Own XLR Cables: A Step by Step Guide - Studio DIY — The Home Studio Archive
Home Studio DIY: How to Make Custom XLR Cables — Boom Box Post
Home Studio DIY: How to Make Custom XLR Cables — Boom Box Post
the wiring diagram for an xr to rxr - screened cable, including two connectors
the wiring diagram for an xr to rxr - screened cable, including two connectors

  • XLR connectors
  • XLR cable (3-conductor, balanced, shielded)
  • Crimping tool
  • Wire strippers
  • Heat shrink tubing and heat gun
  • Optional: Cable ties or Velcro for cable management

the wiring diagram for an electrical device that is connected to two wires and plugged into each
the wiring diagram for an electrical device that is connected to two wires and plugged into each
How to Build a Microphone Lead Using Neutrik XLR's 2011
How to Build a Microphone Lead Using Neutrik XLR's 2011

Choosing the Right Cable

Selecting the right XLR cable is crucial. It should be a 3-conductor, balanced cable, which means it has two signal conductors and one ground conductor. Ensure it's shielded to protect against interference.

Tip: Consider the length you need and opt for a cable with good shielding and insulation to ensure durability and sound quality.

AD

Selecting XLR Connectors

There are two types of XLR connectors: male and female. Male connectors have three pins that insert into a female connector, which has three holes. For a complete cable, you'll need one of each.

Tip: Remember to choose a connector that's gold-plated for better conductivity and durability.

Preparing the Cable

Before you start, calculate how much cable you'll need. Add a few extra inches for any errors or future modifications.

AD

Using your wire strippers, remove about 2 inches of outer jacket from each end of your cable, exposing the three inner conductors and the braided shield.

Stripping Inner Conductors

Next, strip about ½ inch of insulation from each inner conductor, exposing the copper wire. Be careful not to damage the copper wire during this process.

Tip: Use sharp, high-quality wire strippers to prevent damage to the inner conductors.

AD

Preparing the Outer Shield

Twist the exposed braided shield tightly to prevent it from fraying. Once twisted, fold it back over the cable jacket to ensure it doesn't short out the pins.

Tip: Taping the shield to the cable can add extra security but isn't always necessary.

Crimping the Connectors

Now that your cable is prepared, it's time to connect the XLR connectors. Before crimping, insert the inner conductors into the connector housing, matching the wire colors to the corresponding pins (usually Tip - 2, Ring - 3, Sleeve - 1).

Crimping the Male Connector

Insert the inner conductors into the male connector, ensuring the shield is properly secured under the connector's strain relief.

Place the connector into your crimping tool and apply even pressure, following the tool's instructions for the appropriate crimp force. Once done, check each connection for tightness and to ensure the shield is secure.

Crimping the Female Connector

Repeat the process for the female connector, but this time, insert the inner conductors into the corresponding holes in the connector housing. Make sure the shield is securely grounded to the connector housing.

Tip: Be careful not to overtighten the connector, as it can damage the inner conductors or cause a poor connection.

Finishing Touches

To protect your cable from the elements and provide strain relief, apply heat shrink tubing over the connector junctions. Use a heat gun to shrink the tubing, ensuring it's snug and evenly distributed.

Optional: Add cable ties or Velcro for better cable management, especially useful when working with long cables.

Testing Your XLR Cable

Before using your homemade XLR cable, test it with known working equipment to ensure everything is functioning correctly. A faulty cable can lead to background noise, distorted audio, or no signal at all.

Tip: Start with a low signal and gradually increase the volume to avoid damaging your equipment.

Congratulations, you've just created your own XLR cable! With practice, building custom XLR cables can save you money and allow you to tailor your equipment to your specific needs. Now, go forth and connect with confidence.

AD