how to build gold sluice box

"Crafting Your Gold Rush: A Step-by-Step Guide to Build Your Own Gold Sluice Box"

By Thomas Robinson
AD

Embarking on a gold prospecting adventure? One of the first tools you'll want to build is a gold sluice box, a device that uses running water to separate the heavier gold from the lighter gravel and dirt. Building your own gold sluice box not only saves you money, but it's also a rewarding DIY project. Let's dive into how to build your own gold sluice box step by step.

Before you start, remember that gold sluices come in various designs and sizes. For this guide, we'll focus on a simple, efficient, and portable design that's ideal for both new and experienced prospectors. Grab your tools and materials, and let's begin!

Gather Your Tools and Materials

To build your gold sluice box, you'll need the following tools and materials:

AD
the parts of a storage rack with labels and instructions for each item on it, including description
the parts of a storage rack with labels and instructions for each item on it, including description
A Recirculating Sluice Box for Gold Prospecting
A Recirculating Sluice Box for Gold Prospecting
DIY mini sluice box out of household items #01 How to make
DIY mini sluice box out of household items #01 How to make

  • Circular saw or handsaw
  • Drill ( mitral saw or hole saw attachment)
  • Tape measure
  • Pencil
  • Clamps
  • Hacksaw
  • Sandpaper (120-grit)
  • Waterproof wood glue
  • Stainless steel wood screws (1 1/4" and 2")
  • Sheet metal screws (1/2" and 1 1/4")
  • Aluminum flashing or sheet metal (36" x 8' - 24 or 36 gauge)
  • Plywood (1/4" thick - 4' x 8' sheet)
  • Corrugated plastic pipe (2" diameter - 10' length)
  • Riffle material (carpenter'sBLTN vampire batten, plastic/rubber edge trim, or hard plastic kitchen cutting board - 1/2" x 1 1/2")
  • Niagara mat (optional - 1/8" rubber or plastic material with small slots)

7 Easy DIY Gold Panning Equipment You Can Try - My Simple Need
7 Easy DIY Gold Panning Equipment You Can Try - My Simple Need
Cheap Sluice Box That GETS GOLD
Cheap Sluice Box That GETS GOLD

Measure and Cut the Plywood

Using a tape measure and pencil, measure and mark the following dimensions on your plywood sheet:

AD
  • Near end: 18" x 12" (base of your sluice box entrance)
  • Middle section: 48" x 12" (main body of the sluice box)
  • Far end: 16" x 12" (exit of your sluice box)

Using your circular saw or handsaw, carefully cut along these lines to create three sections.

Assemble the Sluice Box Base

Lay out the three sections you just cut, with the 18" piece at one end, then the 48" piece in the middle, and the 16" piece at the other end. Apply waterproof wood glue along the overlapping edges, then clamp them together. Drill and countersink pilot holes approximately 2" apart along the edges, then secure the sections together using 1 1/4" stainless steel wood screws.

AD

Sand the edges and corners of your sluice box base to smooth out any rough areas and remove splinters.

Create the Sluice Box Walls and Riffles

Now that you have the base of your gold sluice box, it's time to add the walls and riffles that help capture the heavier materials, including gold.

Add the Sluice Box Walls

Measure and mark the following dimensions on your aluminum flashing or sheet metal for the walls:

AD

  • Near end walls: 18" x 6" (for the entrance)
  • Middle section walls: 48" x 6" (for the main body)
  • Far end walls: 16" x 6" (for the exit)

Cut these pieces using tin snips or a hacksaw, then attach them to the inside edges of your sluice box base using sheet metal screws. Ensure the walls are vertical and even.

Install the Riffle Material

Measure and mark your riffle material (vampire batten, edge trim, or cutting board) at 1 1/2" intervals along the length of your sluice box. Cut these pieces to create individual riffles.

Starting at the entrance of your sluice box, apply a small amount of waterproof wood glue to the underside of each riffle, then position it at the marked intervals. Secure each riffle using a few 1 1/4" stainless steel wood screws driven into the base and walls of your sluice box. Ensure the riffles are perpendicular to the direction of water flow.

Optional: Install a Niagara mat at the bottom of your sluice box for added efficiency in capturing fine gold particles.

Add the Sluice Box Feed Tray and_class="_** classifier

AD