how to bleed brakes on atv

How to Bleed Brakes on ATV: Step-by-Step Guide

By Joseph Harris
AD

Bleeding your ATV's brakes is a crucial maintenance task that's not only crucial for optimal performance but also ensures your safety while riding. Regularly bleeding your ATV's brakes ensures they're free of air and contaminants, enhancing responsiveness and preventing potential accidents caused by low hydraulics. In this guide, we will walk you through the process, making it simple and accessible for everyone.

Before we start, ensure you have all the necessary tools and safety gear. You'll need a floor jack, jack stands, bleeder wrench, clear plastic tubing, brake fluid, and latex gloves to protect your hands. Always remember to wear appropriate clothing, gloves, and eye protection when performing any kind of maintenance.

Understanding the Brake System

Firstly, you need to understand how your ATV's brake system works. Most ATVs use a hydraulic brake system, consisting of master cylinders, brake lines, calipers, and rotors. Air is the enemy here, as it reduces the effectiveness of your brakes by compressing and forming bubbles in the fluid, creating a spongy feel when you apply the brakes.

AD
How to Bleed ATV and UTV Brakes
How to Bleed ATV and UTV Brakes
How to bleed ATV brakes? A start-to-finish guide
How to bleed ATV brakes? A start-to-finish guide
How To Bleed ATV Brakes
How To Bleed ATV Brakes

Bleeding the brakes is the process of removing air from the system by opening the bleeder screws on each caliper, allowing you to force out the bubbles, ensuring a solid brake pedal, and ultimately, better braking power.

Preparation

Start by parking your ATV on a flat surface and chock the wheels to prevent it from rolling. Using a floor jack, lift the ATV off the ground and support it securely with jack stands. This will give you clear access to work underneath.

How to Bleed ATV Brakes and Rebuild a Rear Master Cylinder | Partzilla.com
How to Bleed ATV Brakes and Rebuild a Rear Master Cylinder | Partzilla.com
How to Bleed the Brakes on a Four Wheeler
How to Bleed the Brakes on a Four Wheeler

Next, locate the bleeding screws on each caliper. These are usually found at the bottom of the caliper and are capped with a rubber or plastic cap. Using a grease pencil or marker, mark each bleeder screw. This will help you keep track of the order, ensuring you don't introduce air back into the system.

Bleeding the Brakes

Before starting, ensure the master cylinders are topped off with brake fluid. Squeeze the brake lever repeatedly to prime the system, forcing more brake fluid into the lines and calipers. When you release the lever, you should hear the calipers grip the rotors.

AD

Now, you're ready to begin bleeding the brakes. Start with the right caliper (forward) and work your way back. Using a 3/8" wrench, slowly open the bleeder screw a quarter turn at a time, one complete revolution at most. Using a piece of clear plastic tubing, connect the other end to the bleeder screw. Place the tube in a clear container filled with brake fluid.

Have a helper firmly press and hold the brake lever. As the lever is pressed, you should see brake fluid being forced out of the tube. When the lever reaches its fully compressed state, quickly close the bleeder screw. Repeat this process until no air bubbles are evident in the fluid.

Testing the Brakes

After bleeding all calipers, it's crucial to test the brakes to ensure the system is holding pressure and providing the correct response. With your ATV still securely supported, slowly lower it to the ground.

AD

Starting with the rear brake, apply light pressure to check for fluid leaks around the calipers or master cylinders. Then, apply full pressure to test the bite point. You should feel a firm response without any sponginess. Repeat the process with the front brake.

Final Checks

After testing, it's a good idea to double-check your handiwork. Inspect each caliper for any signs of leaks. Tighten any bleeder screws that may have loosened during the bleeding process.

Lastly, clean up your work area and dispose of the old brake fluid responsibly. Brake fluid is hazardous to the environment, so ensure it doesn't pollute any water sources.

AD

Regularly bleeding your ATV's brakes is essential for optimal performance and safety. It's a straightforward process that can be easily done at home, saving you time and money. Always remember to check your owner's manual for specific instructions, as different ATVs may have slightly different procedures. Happy riding!

AD