how to bleed a motorcycle hydraulic clutch

How to Bleed a Motorcycle Hydraulic Clutch: Step-by-Step Guide

By Mark Wilson
AD

If you're a motorcycle enthusiast, chances are you've found yourself with a stiff or hard-to-engage clutch at some point. This often indicates that it's time to bleed your hydraulic clutch. Bleeding a motorcycle hydraulic clutch isn't as daunting as it sounds. It's a straightforward task that anyone can do with the right tools and a bit of know-how. Here's a comprehensive guide on how to bleed a motorcycle hydraulic clutch.

Before we dive in, remember that this process requires precision and patience. It's crucial to follow the steps carefully to avoid damaging your bike or causing injury. Always ensure you're working in a well-lit, stable area, and have the correct tools for the job.

Understanding Your Motorcycle's Clutch System

Before bleeding a hydraulic clutch, it's essential to understand its design and operation. Most motorcycles use a hydraulic clutch to activate the clutch release mechanism. This system includes a clutch master cylinder, which is linked to the clutch lever, and a slave cylinder, which engages the clutch.

AD
How To Bleed A Hydraulic Clutch, Fix Soft Or No Clutch Pressure
How To Bleed A Hydraulic Clutch, Fix Soft Or No Clutch Pressure
How To Service A Motorcycle’s Hydraulic Clutch
How To Service A Motorcycle’s Hydraulic Clutch
How to Make a Simple Clutch or Brake Bleeding Kit
How to Make a Simple Clutch or Brake Bleeding Kit

A properly functioning hydraulic clutch depends on consistent fluid hydraulic pressure. Over time, this system can develop air bubbles, which can lead to poor clutch performance. Bleeding the clutch helps to remove these air bubbles and restore full hydraulic pressure.

Gathering Necessary Tools and Materials

Before you begin, ensure you have all the necessary tools and materials on hand. These include:

HOW TO TECH | FIT A HYDRAULIC CLUTCH - Australasian Dirt Bike Magazine
HOW TO TECH | FIT A HYDRAULIC CLUTCH - Australasian Dirt Bike Magazine
Adjust Motorcycle Clutch Cable at Home
Adjust Motorcycle Clutch Cable at Home
  • Auburn Elixir Misty Tool (or equivalent) to bleed the clutch
  • Clutch fluid (ensure it matches your bike's manufacturer specifications)
  • Panel gap pick or a flathead screwdriver (to access the bleeder valve)
  • Grease (to keep the bleeder valve area lubricated and contamination-free)
  • Plastic cling wrap or a rubber band (to protect the clutch lever)
  • Rags and a bowl or container (for catching excess clutch fluid)

Preparing Your Motorcycle for Bleeding

Start by prep your motorcycle by preparing the environment, protecting it from dirt or debris. Wipe down the immediate area around the bleeder valve to prevent dirt from contaminating the clutch system. Next, coat the bleeder valve with grease to keep it lubricated and make bleeding easier.

Turn the clutch arm slowly to ensure the system is free of any unexpected resistance or noise. If you encounter any issues, address them before proceeding as they could signal underlying problems that may worsen during the bleeding process.

AD

Bleeding the Motorcycle Hydraulic Clutch

Now that you've prepared your motorcycle, you can begin the bleeding process. Remember that this process should be done with a friend to assist you, as you'll need someone to operate the clutch lever while you monitor the bleeder valve.

Wrap the clutch lever with plastic cling wrap or a rubber band to protect it from corrosion in case of any clutch fluid spillage. Position the bowl or container under the bleeder screw to catch the expelled fluid and air.

Bleeding the Clutch: Step-by-Step

Use the Auburgh Elixir Misty Tool to open the bleeder valve very slowly. Have your assistant operate the clutch lever slowly and in small increments, ensuring the lever is fully released before each downstroke. While the lever is up, close the bleeder valve and tighten it gently. Repeat this process until no more air bubbles appear in the expelled fluid, and the lever action feels smooth and strong.

AD

Once you've bled all the air from the system, top off the clutch master cylinder with fresh clutch fluid, ensuring it's completely full. Close the reservoir cap and operate the clutch lever several times, allowing the new fluid to circulate and settle. Finally, wipe off any spilled fluid, clean up your workspace, and you're all done!

Post-Bleed Motorcycle Maintenance

After successfully bleeding your motorcycle hydraulic clutch, it's crucial to perform a post-maintenance check. Re-check the clutch lever for smooth operation and correct fluid levels in the master cylinder. If everything checks out, your clutch should feel as good as new, providing smooth and responsive shifting.

Bleeding a motorcycle hydraulic clutch might sound intimidating, but with the right tools and techniques, it's a simple task that can be done in your own garage. Regular preventative maintenance like this will keep your bike running smoothly and safely, extending its lifespan and your riding pleasure. So, the next time you notice a sluggish clutch, don't hesitate – grab your tools and get bleeding!"

AD
AD