"Revive Your Throw: How to Bind an Unresponsive Yoyo"
Are you struggling with an unresponsive yoyo that seems to have lost its wind? Don't be disheartened; your beloved yoyo can serve you again with a little tender loving care and the right technique. Binging an unresponsive yoyo is a skill that every yoyo enthusiast should master. This comprehensive guide will walk you through the process, ensuring your yoyo performs optimally once more. Let's dive right in!
Before we delve into the binding process, it's crucial to understand why your yoyo might have become unresponsive in the first place. This could be due to a buildup of dirt and debris within the yoyo's bearing, or your yoyo might be suffering from a 'death-break', where the metal surfaces of the yoyo have become oxidized and sticky.
Preparing Your Yoyo for Binning
The first step in binding an unresponsive yoyo is to disassemble it and thoroughly clean the components. This will allow you to reach the root of the problem and ensure that your binding process is effective.
Begin by removing the two halves of your yoyo. Typically, this involves unscrewing the yoyo to expose the bearing and weights. Once disassembled, inspect the yoyo's components for any signs of dirt or corrosion. If you find significant buildup, proceed to the next step. Otherwise, you might only need to lubricate the yoyo.
Cleaning the Bearing
A dirty or seized bearing is a common cause of unresponsiveness in yoyos. To clean the bearing, you'll need some rubbing alcohol, cotton swabs, and a small tool to remove the bearing from the yoyo shell.
First, use the tool to carefully pry the bearing out of the yoyo shell. Next, submerge the bearing in rubbing alcohol and use cotton swabs to gently clean the surfaces. After the bearing has been cleaned, dry it off and set it aside.
Removing Corrosion
If your yoyo has become unresponsive due to 'death-break', you'll need to remove the sticky oxide layer from the yoyo's metal surfaces. This can be done using a process called 'ovenbiyo', which involves heating the yoyo in the oven to burn off the oxidation.
Preheat your oven to about 400°F (200°C) and place your yoyo's components on a baking sheet. Allow the yoyo to heat for approximately 15-20 minutes, being careful not to overheat or burn the plastic components. After heating, remove the yoyo from the oven and let it cool.
Binning the Yoyo
Once your yoyo's components have been cleaned and any corrosion removed, it's time to bind the yoyo. Binning involves applying a thin layer of responsive string to the yoyo's string gap, allowing for better performance and responsiveness.
There are several types of binding wax available, each with its unique properties. Choose a wax that best suits your yoyo and playstyle. For example,, high-viscosity waxes are ideal for unresponsive yoyos, while low-viscosity waxes are better for slim or wide-string yoyos.
Applying the Binding Wax
Begin by heating a small amount of binding wax in your hands to melt it slightly. This will make the wax more malleable and easier to apply.
Next, take a small amount of melted wax and rub it onto the yoyo's string gap using your fingers. Ensure the wax is evenly distributed across the gap, creating a thin, even layer. Be careful not to apply too much wax, as this can lead to excess friction and cause the yoyo to feel 'tight'.
Testing the Binned Yoyo
After applying the binding wax, let the yoyo sit for a few minutes to allow the wax to set. Once set, reassemble your yoyo and test it out on the string.
You should now notice an improvement in your yoyo's responsiveness. If your yoyo still feels unresponsive, you may need to apply a second coat of binding wax or adjust the amount of wax used.
The art of binding an unresponsive yoyo is a skill that requires practice and patience. With the right technique and a little experimentation, you'll be bringing your unresponsive yoyos back to life in no time. Happy yoyoing!