how to attach throttle cable to carb

Step-by-Step: how to Attach Throttle Cable to Carburetor

By Brian Smith
AD

If you're working on your motorcycle's fuel system, attaching the throttle cable to the carburetor can seem daunting. But don't worry, it's a straightforward process with the right steps and a bit of patience. This guide will walk you through the process, ensuring you get it right the first time.

Before you start, gather your tools: needle-nose pliers, a screwdriver, and any specific tool your throttle cable may require. Also, have your new throttle cable ready, along with the adjustment screws that came with it. Safety first, so ensure your motorcycle is on a level surface and the engine is cool.

Preparation

Before diving into the attachment process, let's prepare your carburetor and throttle cable.

AD
Induction Guide for Building Big-Inch LS Engines • LS Engine DIY
Induction Guide for Building Big-Inch LS Engines • LS Engine DIY
Carb Synchronization Procedure | Randakk's Blog
Carb Synchronization Procedure | Randakk's Blog
485K views · 7.8K reactions | Since the pilot and main circuits have an influence on the mid range, you always want to dial in the needle last. In addition to needle taper and height, some carbs can tune the s | One-Up Moto Garage
485K views · 7.8K reactions | Since the pilot and main circuits have an influence on the mid range, you always want to dial in the needle last. In addition to needle taper and height, some carbs can tune the s | One-Up Moto Garage

The first step is to remove any old or damaged cable. Use your screwdriver to remove the cable adjustment screw. Then, carefully pull out the old cable from the track or pulley it's connected to. If it's stuck, you can use some WD-40 to help loosen it up.

Inspect Your Carburetor

Once the old cable is out, inspect the hole in your carburetor where the cable enters. Ensure there are no debris or damage that could impair the new cable's function.

How to Install Push Pull Throttle Cables
How to Install Push Pull Throttle Cables
Really practical Tip and Trick! How to quickly make a reliable loop on a steel cable yourself? #diy
Really practical Tip and Trick! How to quickly make a reliable loop on a steel cable yourself? #diy

If there are any issues, clean out the hole using a piece of wire or a small brush. If the hole is damaged, you might need to have your carburetor serviced or replaced.

Prepare Your New Throttle Cable

Uncoil your new throttle cable and check for any kinks or bends. If there are any, straighten them out gently to maintain the cable's functionality.

AD

Now, let's move on to attaching the new cable to your carburetor.

Attaching the Throttle Cable

With your carburetor and new cable prepared, you're ready to attach the new cable.

Start by taking the end of the cable with the adjustment nut and inserting it into the hole in the carburetor. Use the adjustment nut to secure the cable in place. Tighten it gently to hold the cable steady but not too tight to prevent damage.

AD

Route the Cable Properly

To ensure the cable functions correctly, it's crucial to route it properly. Route the cable from the carburetor towards the handlebar. Keep it away from any moving parts, heat sources, or areas where it could get damaged.

Use cable ties oroute channels to keep the cable in place. This will prevent it from flapping around or getting caught on other parts of your motorcycle.

Connect the Cable to the Throttle

Once the cable is routed correctly, you can connect it to the throttle on your handlebar. There should be a small hole or clip where the cable can be secured. Insert the end of the cable into this hole and secure it in place.

AD

Use your needle-nose pliers to make any necessary adjustments to the cable to ensure it's properly connected. Be careful not to overtighten or bend the cable at this point.

Adjusting the Cable

With the cable attached, it's time to adjust it for optimal performance.

First, start the engine. Slowly open the throttle and check if the engine's revs increase as expected. If not, you'll need to adjust the cable using the adjustment nut on the carburetor.

Tuning the High-Speed Screw

The high-speed screw, also known as the main jet or engine speed adjustment screw, controls the engine speed at high RPMs. To adjust it, open the throttle fully and then slowly close it while listening to the engine.

Tighten the screw if the engine speed drops off too fast, or loosen it if the engine speed stays too high when you close the throttle. Be careful not to over-tighten, as this can damage the carburetor.

Tuning the Low-Speed Screw

The low-speed screw, also called the idle adjust screw, controls the engine's idle speed. To adjust it, close the throttle until the engine is running at its normal idle speed.

Adjust the idle speed by turning the screw clockwise to increase the idle speed or counterclockwise to decrease it. Be careful not to over-rev the engine.

Finally, take your motorcycle for a test ride to ensure everything is working correctly. Keep an eye on the throttle cable to ensure it's functioning properly and not interfering with any other parts. Regular checks and maintenance will help extend the lifespan of your new throttle cable. Happy riding!

AD