how to adjust the valves on a 400ex

Mastering Your 400EX: A Step-by-Step Guide to Adjusting Valves

By John Williams
AD

The 400EX, a-deux-stroke Trials machine produced by Yamaha, is renowned for its robustness and reliability. However, like any engine, it requires regular maintenance to keep it running smoothly. One crucial aspect of this maintenance is adjusting the valves. A well-adjusted valve ensures optimal engine performance, fuel efficiency, and longevity of the engine. This guide will walk you through the process of how to adjust the valves on a Yamaha 400EX.

Before we dive into the specifics, it's essential to note that this procedure requires some mechanical aptitude and the right tools. If you're unsure about any part of the process, don't hesitate to consult a professional mechanic. Now, let's get started.

The Basics of Valve Adjustment

Valve adjustment involves setting the clearance between the valve and its seat to a specified tolerance. This clearance, often referred to as the valve gap or valve clearance, ensures that the valve opens and closes efficiently. Too little clearance can cause the valve to stick, leading to engine damage. Too much clearance can result in excessive engine noise and reduced performance.

AD
Step by Step - How to measuring & adjust valve clearances
Step by Step - How to measuring & adjust valve clearances
How to Adjust Valves on OHV Small Engines (Valve Clearance / lash)
How to Adjust Valves on OHV Small Engines (Valve Clearance / lash)
How To: Valve Adjustment Spacing - KLR650
How To: Valve Adjustment Spacing - KLR650

For a 400EX, the recommended valve clearance for both the intake and exhaust valves is 0.06 to 0.08mm for cold engines and 0.04 to 0.06mm for hot engines. The process differs slightly depending on whether the engine is cold or hot, so we'll cover both scenarios.

Preparation: Tools and Engine Condition

Before you start, ensure you have the necessary tools. You'll need a feeler gauge set (with blades from 0.02 mm to 0.10 mm), a wrench (usually 8mm or 10mm, depending on your 400EX model), a screwdriver, valve adjustment tools (including a spring compressor), and a torque wrench. Also, make sure the engine is in good condition, with no signs of excessive wear or leakage.

Valve Removal & Installation Method 2 : Specialty Tool (Very Easy)
Valve Removal & Installation Method 2 : Specialty Tool (Very Easy)
valve adjustment clearance- lesson 3c
valve adjustment clearance- lesson 3c

For cold valve adjustment, the engine should be at normal outdoor temperature. For hot valve adjustment, start the engine and let it run until it reaches normal operating temperature. Always remember to let the engine cool down before adjusting the valves to prevent any burns.

Accessing the Valves

To access the valves on your 400EX, you'll need to remove the fuel tank, the valve cover, and the cylinder head cover. Start by draining the fuel. Then, remove the fuel tank, followed by the seat and air filter housing. With these components out of the way, you can access the valve cover and remove it. Finally, remove the cylinder head cover to expose the valves.

AD

Once the valves are accessible, you can proceed with the valve clearance check and adjustment. Before you start, it's a good idea to number the valves to ensure you reassemble everything correctly later.

Valve Adjustment: Cold Engine

With the engine cold, the valves are easiest to adjust. Begin by checking the clearance with a feeler gauge. Insert a gauge into the space between the valve stem and the cam lobe, under the rocker arm. If the gauge slips in easily, the clearance is too large. If it sticks but moves freely, the clearance is within the recommended range. If it doesn't move at all, the clearance is too small.

To adjust the clearance, you'll need to bend the valve shims. The shims are located at the top of the valves, beneath the springs and retainers. Using the appropriate valve adjustment tools, compress the spring and remove the retainer. Then, use the feeler gauge to measure the shim. After measuring, you can bend the shim to achieve the desired clearance. Remember, it's best to err on the side of a slightly too small clearance, as you can always make it larger but not smaller without removing more material from the shim.

AD

Valve Adjustment: Hot Engine

Adjusting the valves on a hot engine is a bit more complex due to the expansion of the engine components. The process is similar, but you'll need to account for the additional clearance required due to the heat. Typically, you'll want to aim for a clearance that's about 0.02 mm larger than the cold clearance when the engine is hot.

To get the hot clearance, heat the engine to normal operating temperature, then recheck the valve clearance. Again, use a feeler gauge to measure the clearance and make any necessary adjustments to the shims. Always remember to let the engine cool down before rechecking the clearance to prevent any inaccuracies in your measurements.

Reassembly and Final Checks

Once you've adjusted the valves, it's time to reassemble everything. Start by putting the valve shims and retainers back in place. Then, reinstall the cylinder head cover, valve cover, and any other components you removed. Make sure everything is properly torqued and sealed to prevent any leaks.

AD

After reassembly, start the engine and let it warm up. Check for any leaks or unusual noises. If everything seems in order, your Yamaha 400EX's valves are properly adjusted, and your engine should be running smoothly.

Regularly adjusting your 400EX's valves is a crucial part of maintaining your engine's performance and longevity. With a little bit of know-how and the right tools, it's a task you can tackle yourself. So, grab your feeler gauge and get to work. Your Yamaha 400EX will thank you for it!

AD