how to adjust points on a distributor

How to Adjust Points on a Distributor

By Olivia Wilson
AD

Adjusting points on a distributor, often referred to as timing a distributer, is a crucial aspect of maintaining optimal engine performance in vehicles. This process involves setting the distributor's mechanical advance curve to match the ignition curve of the engine, ensuring that the spark plugs fire at the correct moment for efficient combustion. In this comprehensive guide, we'll walk you through the process of how to adjust points on a distributor, complete with detailed steps and valuable tips.

Before we dive into the process, it's essential to understand that distributors may vary depending on the make and model of your vehicle. Some modern cars have electronic ignition systems that don't use distributors or points, so always check your vehicle's specifications first. This guide assumes you're working on a classic or vintage car with a conventional distributor.

Understanding the Distributor and its Components

The distributor is a critical component in the ignition system, responsible for routing spark plugs' electrical current from the ignition system to the spark plugs. It comprises several parts, including the distributor cap, rotor, points, condenser, andLucas setting.

AD
Ignition Distributor: Diagram, Parts, Working, Problems [PDF]
Ignition Distributor: Diagram, Parts, Working, Problems [PDF]
How to Install a Distributor and Set Initial Timing
How to Install a Distributor and Set Initial Timing
How the Ignition Points and Condenser Work
How the Ignition Points and Condenser Work

Points, located inside the distributor, work in conjunction with the condenser to control the flow of electricity to the spark plugs. They open and close according to the engine's crankshaft position, creating an intermittent circuit that generates high voltage needed for ignition. Adjusting points involves calibrating the gap between them to provide the correct spark timing.

Inspecting the Distributor and Points

Before you begin adjusting the points, it's crucial to inspect the distributor and its components for any signs of wear or damage. Check for carbon tracks on the outside of the distributor cap, as they can indicate a weak or leaking spark. Also, examine the points themselves for signs of burns, pitting, or excessive erosion. If any of these issues are present, it may be necessary to replace the points or the entire distributor before attempting to adjust them.

How to Install A distributor in a 350 Chevy
How to Install A distributor in a 350 Chevy
Three point starter
Three point starter

After checking the external components, remove the distributor cap and rotate the distributor shaft to simulate engine operation. Observe the points as they open and close. They should move smoothly and consistently, without any hesitation or binding. If the points are not functioning correctly, they may need to be replaced or the distributor may require further inspection.

Adjusting the Points

To adjust the points, you'll need a spark plug gap gauge, a feeler gauge set, a tachometer, and a timing light with an ignition pick-up lead. Begin by removing the distributor cap and rotor. Disconnect the ignition coil wire from the distributor cap.

AD

Using the timing light, set the engine to Top Dead Center (TDC) on the compression stroke of cylinder number one. This position corresponds to the index mark on the distributor's housing aligning with the TDC mark on the engine block. Once the engine is at TDC, loosen the distributor hold-down clamp to allow the distributor to rotate.

Setting the Initial Timing

Before adjusting the points, it's essential to set the initial ignition timing. This step ensures that the engine has a base timing setting to work from, allowing for more accurate point adjustments. To set the initial timing, connect the timing light's ignition pick-up lead to the number one spark plug wire.

Start the engine and allow it to warm up to its normal operating temperature. Once the engine is warm, shine the timing light onto the crankshaft pulley or Overhead Cam (OHC) pulley, ensuring it's lit evenly. As the engine runs, the timing mark on the pulley should briefly pass through the light's beam. When this happens, quickly note the degree mark on the timing scale that corresponds to the mark on the pulley. This reading represents your engine's initial ignition timing.

AD

Adjusting the Mechanical Advance

The mechanical advance refers to the distributor's centrifugal and vacuum advance mechanisms, which adjust the spark timing according to engine RPM. These mechanisms consist of weights mounted on the distributor shaft that, as they spin, cause the distributor to advance the spark at higher RPMs. At lower RPMs, the vacuum advance pulls on the distributor, retarding the spark for better combustion.

Before adjusting the points, it's essential to ensure that both the centrifugal and vacuum advance mechanisms are functioning correctly. To test the centrifugal advance, start the engine and increase the RPMs gradually. As the engine speed increases, the distributor should rotate slightly in the ignition retarding direction. If it doesn't, or if it retards more than expected, the centrifugal advance may be faulty or misadjusted.

To test the vacuum advance, you can use a vacuum gauge connected to the distributor's vacuum advance port. With the engine running at a steady RPM, the vacuum gauge should read approximately 15-20 inches of mercury (Hg). If the reading is significantly lower or higher than this range, the vacuum advance may need adjustment or repair.

AD

Setting the Final Ignition Timing

With the distributor still loosened, use the spark plug gap gauge to measure the gap between the points. The correct point gap varies depending on the make and model of your vehicle, so consult your vehicle's service manual for the exact specifications. Once you've determined the correct gap, adjust the points as necessary using the feeler gauge set.

To adjust the points, gently bend the upper point (or both points, if necessary) with a pair of narrow-nose pliers until the desired gap is achieved. Be careful not to over-bend or damage the points during this process. After adjusting the point gap, recheck the ignition timing using the timing light and ensure it falls within the manufacturer's specified range.

Once you've verified that the ignition timing is correct and both the centrifugal and vacuum advance mechanisms are functioning properly, tighten the distributor hold-down clamp securely. Reconnect the ignition coil wire to the distributor cap and replace the rotor and distributor cap.

Start the engine and allow it to warm up briefly. Once the engine is running smoothly, you've successfully adjusted the points on your distributor, ensuring optimal engine performance and efficiency. Regularly inspecting and maintaining your vehicle's ignition system will help prevent issues and keep your engine running smoothly.

And there you have it – a comprehensive guide to adjusting points on a distributor. By following these steps and maintaining a regular inspection schedule, you'll keep your engine's ignition system in top shape. Happy wrenching!

AD