How to Fine-Tune Your Dewalt Table Saw Fence
If you're a woodworker with a DEWALT DWE7491RS or DCS7485B table saw, you might find that your fence requires occasional adjustment to ensure accurate and safe cuts. A well-adjusted fence can prevent kickback, make your cuts straighter and more precise, and prolong the life of your blade. Here's a step-by-step guide on how to adjust your DEWALT table saw fence for optimal performance.
Before you begin, ensure your table saw is unplugged to prevent any accidents. Also, this guide assumes you have a basic understanding of table saw safety procedures. Always wear appropriate Personal Protective Equipment (PPE), including safety glasses and a dust mask.
Understanding Your DEWALT Table Saw Fence
The DEWALT DWE7491RS and DCS7485B come with rack and pinion-style fences, which are generally easier to adjust than linear-style fences. The rack and pinion system consists of a toothed bar (rack) and a gear (pinion) that converts linear motion into rotational motion. The fence's positioning can be adjusted by turning the handwheel, which is connected to the pinion.
The fence assembly is secured to the table's surface using two bolts, one on each side of the blade. These bolts allow the fence to move parallel to the blade, ensuring accurate cuts. You'll also notice a fence scale on the front of the fence, which helps you measure the distance from the blade to the fence's edge. This measurement indicates the width of the cut you're about to make.
Initial Fence Adjustment
Upon unboxing your DEWALT table saw, it's a good idea to perform an initial fence adjustment. Start by ensuring the fence is parallel to the blade. Loosen the two fence bolts using a wrench, then slide the fence until it's parallel to the blade. Tighten the bolts gradually and in an alternating pattern to ensure the fence is secure and straight.
Next, ensure the fence is perpendicular to the miter gauge slots. This is important for making accurate 90-degree cuts. Use a combination square or a framing square to check the perpendicularity. Adjust the fence's position as needed until it's perpendicular to the miter gauge slots.
Adjusting the Fence for Perfect Alignment
Over time, the fence on your DEWALT table saw may become misaligned due to repeated use or accidental impacts. When this happens, you'll need to adjust the fence back into perfect alignment. Begin by loosening the fence bolts using a wrench. Next, turn the handwheel to move the fence along the rack until it's lined up with the blade.
Once the fence is aligned with the blade, tighten the fence bolts gradually and in an alternating pattern. This ensures that the fence is secure and won't move during operation. After tightening the bolts, recheck the fence's alignment and perpendicularity to ensure it hasn't shifted during the adjustment process.
Cleaning and Lubricating the Fence
A clean and well-lubricated fence will move smoothly and quietly along the table's surface, ensuring accurate cuts and prolonging the fence's lifespan. To clean and lubricate your DEWALT table saw fence, start by unplugging the saw and allowing it to cool completely.
Use a degreasing cleaner to remove any sawdust, dirt, or resin buildup from the fence's surface and the rack and pinion system. A brush with stiff bristles can help you reach tight spaces. After cleaning, dry the fence thoroughly to prevent water spots or rust from forming.
Lubricating the Rack and Pinion System
Apply a small amount ofนา 손가락“그 répond to the lubricant to the rack and pinion system. A wheel cleaner or a lubricant specifically designed for table saws works well. Avoid using grease, as it can attract dirt and sawdust, causing the fence to become sticky or stiff over time.
To apply the lubricant, turn the handwheel slowly while applying a consistent amount of lubricant to the rack and pinion system. This will ensure that the lubricant is evenly distributed throughout the system. After lubricating, make a few more turns of the handwheel to work the lubricant into the system properly.
Congratulations! You've now successfully adjusted, realigned, and maintained your DEWALT table saw fence. With regular cleaning, lubrication, and adjustments, your fence will remain accurate and functional for many years to come. Always remember to prioritize safety when using your table saw, and never hesitate to seek professional advice if you're unsure about any aspect of fence adjustment or maintenance.