how to add an outlet to an existing outlet

How to Add an Outlet to an Existing Outlet

By David Young
AD

Adding an outlet to an existing circuit can be a challenging task, but with the right guidance, it's a worthwhile DIY project that can enhance your home's electrical capacity. This comprehensive guide will walk you through the process, from understanding your home's electrical system to completing the installation safely and efficiently.

Before you begin, it's crucial to understand that electrical work should always be done by a licensed professional unless you're confident in your abilities and follow local regulations. This guide assumes you have some electrical knowledge and always prioritizes safety.

Assessing Your Home's Electrical System

Before you even think about adding an outlet, you need to understand your home's electrical system. This includes knowing the type of wiring you have, the ampacity of your circuit breakers, and the layout of your electrical panel.

AD
an empty room with the words how to add an outlet in 50 seconds on it
an empty room with the words how to add an outlet in 50 seconds on it
A No Hassle Way to Quickly Add an Electrical Outlet
A No Hassle Way to Quickly Add an Electrical Outlet
how to add extra outlet plugs in an old electrical box with pictures and instructions
how to add extra outlet plugs in an old electrical box with pictures and instructions

Most modern homes in North America use non-metallic (NM) cable, often referred to as Romex. If your home was built before the 1950s, you might have knob-and-tube wiring or aluminum wiring. Both of these require special considerations and may need to be replaced by a professional.

Determining the Circuit

Each outlet in your home is connected to a circuit, which is protected by a circuit breaker in your electrical panel. Before adding an outlet, you need to figure out which circuit has the available capacity. A typical household circuit is 15 or 20 amps and can power several outlets.

How to Wire an Outlet and Add an Electrical Outlet (DIY)
How to Wire an Outlet and Add an Electrical Outlet (DIY)
How to Replace an Electrical Outlet. Seriously, YOU can do this.
How to Replace an Electrical Outlet. Seriously, YOU can do this.

Use a circuit identifier tool or label each outlet and switch during a power outage to determine which outlets are on the same circuit. Look for an open slot on your circuit breaker panel for your new outlet. If there's none, you might need to add a new circuit.

Gathering Materials and Tools

Once you've identified the circuit and determined that it can accommodate an additional outlet, gather your materials and tools. You'll need a new outlet, non-metallic (NM) cable, cable connectors, a fish tape, a wire stripper, a drill with a hole saw (if the outlet isn't close to an existing one), and safety equipment like gloves and goggles.

AD

Remember to buy a high-quality outlet that's UL-listed, meaning it meets safety standards. It's also a good idea to buy a few extra materials in case of mistakes or unexpected problems.

Preparing the Area and Installing the Outlet

Before you start any work, ensure the power to the circuit is off by turning off the circuit breaker and testing the wires with a non-contact voltage tester. If the installer is unsure about their safety practices, they should consult a licensed electrician.

The next step is to drill a hole for the new cable if it's not near an existing outlet. Use a hole saw that's slightly larger than the cable to make the hole. Then, feed the cable through the hole using a fish tape.

AD

Wiring the Outlet

Strip the insulation off the cable using a wire stripper, and then connect the wires to the outlet. Since NM cable has two hot wires, a neutral wire, and a ground wire, it's essential to match the correct wire to the terminal.

Most outlets have screws marked 'hot', 'neutral', and 'ground'. Connect the black wires to the hot screws, the white wire to the neutral screw, and the green or bare wire to the ground screw. Twist the wires clockwise into the terminal screws, then tighten them with a screwdriver.

Securing and Testing the Outlet

Secure the outlet to the box using screws, then tuck the wires into the box and install the cover plate. Be careful not to overtighten the screws and damage the outlet.

AD

Now, turn the power back on and test the outlet using a voltage tester to ensure it's live. Plug in a small electrical appliance to make sure the outlet works as expected.

Adding an Outlet to an Existing Outlet

If you're adding an outlet next to an existing one, the process is slightly simpler. You'll use a 'pigtail' connection to tap into the existing outlet's wires.

First, remove the existing outlet cover plate and unscrew the outlet. Connect a piece of NM cable to each of the outlet's wires using wire connectors (wire nuts). This is the 'pigtail' connection.

Wiring the New Outlet

Strip the insulation off the pigtail connections and connect them to the new outlet. Match the wire colors to the correct terminal screws, just like you did with the first outlet. Then, secure the new outlet to the box and install the cover plate.

Test the new outlet to ensure it works correctly. If it doesn't, you might have made a wiring mistake, and you should consult a professional.

Ganging Outlets

If you're installing multiple outlets side by side (ganging), the process is similar to adding an outlet to an existing one. You'll connect each new outlet to the one next to it, using pigtail connections.

Remember to leave enough room between the outlets for your fingers to reach the electrical plugs. Also, ensure that you don't exceed the circuit's ampacity by adding too many outlets.

Adding an outlet to your home's electrical system can be a rewarding DIY project, bringing new life to your spaces. However, it's crucial always to prioritize safety, know your limits, and consult a professional when necessary. Happy improving!

AD