how to access drain pump on whirlpool duet washer

How To Access Drain Pump On Whirlpool Duet Washer

By Kevin Rodriguez
AD

If your Whirlpool Duet washer's drainage system isn't performing as it should, you might need to access and repair the drain pump. Don't worry; this guide will walk you through the process step-by-step, ensuring you understand how to safely troubleshoot and fix this issue.

Before you begin, ensure the washer is turned off and unplugged. Also, have your Whirlpool Duet's model number and user manual nearby, as repairs may vary depending on the model.

Understanding Your Washer's Drain Pump

Your Whirlpool Duet washer's drain pump is located at the bottom of the appliance. It pumps water from the washer tub to the drain hose, usually situated at the back of the washer. If your washer isn't draining, it's likely due to a faulty pump.

AD
Whirlpool Washer Won’t Drain - Ready To DIY
Whirlpool Washer Won’t Drain - Ready To DIY
Whirlpool Washer Won't Drain? Drain Pump #W10536347
Whirlpool Washer Won't Drain? Drain Pump #W10536347
Your Whirlpool washer stuck on sensing fill? try these fixes
Your Whirlpool washer stuck on sensing fill? try these fixes

To access the pump, you'll need to remove the washer's bottom panel. The process varies slightly depending on your model, so let's break it down for two common types:

Removing the Bottom Panel in Whirlpool Duet Washer Models WTW5600DW and WTW4800SD

1. **Disconnect the Drain Hose**: Begin by disconnecting the drain hose from the back of the washer. You may need to use a flathead screwdriver to pry off the clamp holding it in place.

Whirlpool Duet Water Pump Drain Catch
Whirlpool Duet Water Pump Drain Catch
a man is opening the door of an open refrigerator with his hand on the handle
a man is opening the door of an open refrigerator with his hand on the handle

2. **Locate and Remove Screws**: On the bottom of the washer, find the four screws near the feet that secure the bottom panel. Unscrew these and set them aside.

Removing the Bottom Panel in Whirlpool Duet Washer Models WTW5000DW and WTW4000SD

1. **Disconnect the Pump and Motor Harness**: Start by disconnecting the pump and motor harness from the terminal at the back of the washer. This is usually held in place by a single screw.

AD

2. **Remove the Bottom Cover**: The bottom cover on these models is held in place by clips. Carefully pry it out using a flathead screwdriver, starting from one corner.

Accessing and Replacing the Drain Pump

Once you've removed the bottom panel, you should see the drain pump. Before you proceed, take a clear photograph of the pump and its hose connections to help you remember how to reassemble it.

To disconnect the hoses, use a flathead screwdriver to turn the clamps counterclockwise, then gently pull the hoses off the pump. If the hoses are stuck, you might need to use a bit of force, but be careful not to damage them.

AD

Inspecting and Replacing the Drain Pump Bearing

First, let's check the drain pump's bearing. If it's making a loud, grinding noise, it's likely worn out and needs replacement. To access the bearing, you'll need to remove the impeller (the rotating part inside the pump).

1. **Remove the Impeller**: Using a flathead screwdriver, carefully pry the impeller out. It might be tight, so you may need to use some force.

2. **Check the Bearing**: Once the impeller is out, you should be able to see the bearing. If it's rotatable, give it a spin. If it's stiff or makes noise, replace it with a new one.

AD

Replacing the Entire Drain Pump

If the bearing checks out, or you've decided to replace the entire pump, follow these steps:

1. **Remove the Old Pump**: Using a wrench, loosen and unscrew the pump from its mount. Once it's loose, pull it out.

2. **Install the New Pump**: Position the new pump in place, making sure the inlet and outlet match the old ones. Secure it with screws.

3. **Reconnect the Hoses**: Replace the hoses onto the pump, ensuring they're securely fastened with the clamps.

Reassembling Your Whirlpool Duet Washer

Now that the pump is replaced or repaired, it's time to put your washer back together:

1. **Reconnect the Harness**: If your model has a detachable harness, reconnect it at the back of the washer. Secure it with the screw you removed earlier.

2. **Replace the Bottom Panel**: Carefully replace the bottom panel, ensuring all screws (or clips) are securely in place.

3. **Reconnect the Drain Hose**: Reattach the drain hose to the back of the washer, making sure it's securely fastened.

Once your washer is reassembled, turn it back on and run a test cycle to ensure the drainage issue is resolved. If everything works correctly, your Whirlpool Duet washer is as good as new! However, if you're still experiencing issues, it's a good idea to consult a professional repair technician.

Regular maintenance and prompt repair of issues can extend your washer's lifespan significantly. So, don't ignore strange noises or other signs of trouble. Keep your Whirlpool Duet washer in top condition, and it will serve you well for years to come.

AD